Ford Milan - 2010 Fuse Box Diagram

Ford Milan - 2010 Fuse Box Diagram

INSTRUMENT PANEL STORAGE COMPARTMENT
The storage compartment may be
used to secure sunglasses or similar
sized objects. Press the button to
open the storage compartment.
AUXILIARY POWER POINT (12VDC)
Power outlets are designed for accessory plugs only. Do not insert
any other object in the power outlet as this will damage the
outlet and blow the fuse. Do not hang any type of accessory or
accessory bracket from the plug. Improper use of the power
outlet can cause damage not covered by your warranty.
The auxiliary power points are
located on the instrument panel and
in the center console utility
compartment.
Do not use the power point for
operating the cigarette lighter
element (if equipped).
To prevent the fuse from being
blown, do not use the power
point(s) over the vehicle capacity of
12 VDC/180W. If the power point or cigar lighter socket is not working, a
fuse may have blown. Refer to
Fuses and relays
in the
Roadside
Emergencies
chapter for information on checking and replacing fuses.
To have full capacity usage of your power point, the engine is required to
be running to avoid unintentional discharge of the battery. To prevent
the battery from being discharged:
do not use the power point longer than necessary when the engine is
not running,
do not leave battery chargers, video game adapters, computers and
other devices plugged in overnight or when the vehicle is parked for
extended periods.
2010 Milan
(mln)
Owners Guide, 1st Printing
USA
(fus)
Driver Controls
74
WARNING:
All occupants of the vehicle, including the driver,
should always properly wear their safety belts, even when an air
bag supplemental restraint system (SRS) is provided.
WARNING:
When possible, all children 12 years old and under
should be properly restrained in a rear seating position.
WARNING:
National Highway Traffic Safety Administration
(NHTSA) recommends a minimum distance of at least 10 inches
(25 cm) between an occupant’s chest and the driver airbag module.
WARNING:
Never place your arm over the airbag module as a
deploying airbag can result in serious arm fractures or other
injuries.
Steps you can take to properly position yourself away from the airbag:
Move your seat to the rear as far as you can while still reaching the
pedals comfortably.
Recline the seat slightly (one or two degrees) from the upright
position.
WARNING:
Do not put anything on or over the airbag module.
Placing objects on or over the airbag inflation area may cause
those objects to be propelled by the airbag into your face and torso
causing serious injury.
WARNING:
Do not attempt to service, repair, or modify the
airbag supplemental restraint system (SRS) or its fuses. See your
authorized dealer.
WARNING:
Modifying or adding equipment to the front end of
the vehicle (including frame, bumper, front end body structure
and tow hooks) may affect the performance of the airbag system,
increasing the risk of injury. Do not modify the front end of the
vehicle.
2010 Milan
(mln)
Owners Guide, 1st Printing
USA
(fus)
Seating and Safety Restraints
134
WARNING:
Do not attempt to service, repair, or modify the
airbag SRS, its fuses or the seat cover on a seat containing an
airbag. Contact your authorized dealer as soon as possible.
WARNING:
All occupants of the vehicle should always wear
their safety belts even when an airbag SRS is provided.
How does the side airbag system work?
The design and development of the side airbag system included
recommended testing procedures that were developed by a group of
automotive safety experts known as the Side Airbag Technical Working
Group. These recommended testing procedures help reduce the risk of
injuries related to the deployment of side airbags (including side air
curtain systems).
The side airbag system consists of
the following:
An inflatable nylon bag (airbag)
with a gas generator concealed
behind the outboard bolster of
the driver and front passenger
seatbacks.
The same warning light,
electronic control and diagnostic
unit as used for the front airbags.
Two crash sensors located under the outboard side of the front seats,
attached near the floor.
Side airbags, in combination with safety belts, can help reduce the risk of
severe injuries in the event of a significant side impact collision.
The side airbags are fitted on the outboard side of the seatbacks of the
front seats. In certain lateral collisions, the airbag on the side affected by
the collision will be inflated. If the front passenger sensing system
detects an empty seat or an unbuckled child or small person, the front
passenger seat-mounted side airbag will be deactivated. The airbag was
designed to inflate between the door panel and occupant to further
enhance the protection provided occupants in side impact collisions.
The airbag SRS is designed to activate when the vehicle sustains lateral
deceleration sufficient to cause the sensors to close an electrical circuit
that initiates airbag inflation.
2010 Milan
(mln)
Owners Guide, 1st Printing
USA
(fus)
Seating and Safety Restraints
143
Side curtain airbag system
WARNING:
Do not place
objects or mount equipment
on or near the headliner at the
siderail that may come into
contact with a deploying side air
curtain. Failure to follow these
instructions may increase the risk
of personal injury in the event of a
collision.
WARNING:
Do not place objects or mount equipment on or
near the side air curtain cover.
WARNING:
Do not lean your head on the door. The side airbag
could injure you as it deploys from the seat.
WARNING:
Do not attempt to service, repair, or modify the side
air curtain system, its fuses, the A, B, or C pillar trim, or the
headliner on a vehicle containing a side air curtain. See your
authorized dealer.
WARNING:
All occupants of the vehicle, including the driver,
should always wear their safety belts even when an inflatable
curtain is provided.
WARNING:
To reduce the risk of injury, do not obstruct or
place objects in the deployment zone of the inflatable curtain.
2010 Milan
(mln)
Owners Guide, 1st Printing
USA
(fus)
Seating and Safety Restraints
145
1. Apply the parking brake, turn
ignition key to off, then remove the
key.
2. Using a screwdriver (or similar
tool), remove the protective cover
to the interlock release access hole
on the console.
3. Insert the screwdriver (or similar
tool) into the access hole and press
downward while pulling the
gearshift lever out of the P (Park)
position and into the N (Neutral)
position.
4. Remove the tool and reinstall the
protective cover.
5. Start the vehicle and release the
parking brake.
If it is necessary to use the above procedure to move the gearshift lever,
it is possible that a fuse has blown or the vehicle’s brakelamps are not
operating properly. Refer to
Fuses and relays
in the
Roadside
Emergencies
chapter.
WARNING:
Do not drive your vehicle until you verify that the
brakelamps are working.
WARNING:
Always set the parking brake fully and make sure
the gearshift is latched in P (Park). Turn the ignition to the off
position and remove the key whenever you leave your vehicle.
WARNING:
If the parking brake is fully released, but the brake
warning lamp remains illuminated, the brakes may not be
working properly. See your authorized dealer as soon as possible.
2010 Milan
(mln)
Owners Guide, 1st Printing
USA
(fus)
Driving
206
Note:
With extended use, the flasher may run down your battery.
FUEL PUMP SHUT-OFF
In the event of a moderate to severe collision, this vehicle is equipped
with a fuel pump shut-off feature that stops the flow of fuel to the
engine. Not every impact will cause a shut-off.
Should your vehicle shut off after a collision due to this feature, you may
restart your vehicle by doing the following:
1. Turn the ignition switch to the off position.
2. Turn the ignition switch to the on position.
In some instances the vehicle may not restart the first time you try to
restart and may take one additional attempt.
WARNING:
Failure to inspect and if necessary repair fuel leaks
after a collision may increase the risk of fire and serious injury.
Ford Motor Company recommends that the fuel system be inspected
by an authorized dealer after any collision.
FUSES AND RELAYS
Fuses
If electrical components in the
vehicle are not working, a fuse may
have blown. Blown fuses are
identified by a broken wire within
the fuse. Check the appropriate
fuses before replacing any electrical
components.
Note:
Always replace a fuse with one that has the specified amperage
rating. Using a fuse with a higher amperage rating can cause severe wire
damage and could start a fire.
15
2010 Milan
(mln)
Owners Guide, 1st Printing
USA
(fus)
Roadside Emergencies
234
Standard fuse amperage rating and color
COLOR
Fuse
rating
Mini
fuses
Standard
fuses
Maxi
fuses
Cartridge
maxi
fuses
Fuse link
cartridge
2A
Grey
Grey
3A
Violet
Violet
4A
Pink
Pink
5A
Tan
Tan
7.5A
Brown
Brown
10A
Red
Red
15A
Blue
Blue
20A
Yellow
Yellow
Yellow
Blue
Blue
25A
Natural
Natural
30A
Green
Green
Green
Pink
Pink
40A
Orange
Green
Green
50A
Red
Red
Red
60A
Blue
Yellow
Yellow
70A
Tan
Brown
80A
Natural
Black
Black
Passenger compartment fuse panel
The fuse panel is located below and to the left of the steering wheel by
the brake pedal. Remove the panel cover to access the fuses.
To remove a fuse use the fuse puller tool provided on the fuse panel
cover.
2010 Milan
(mln)
Owners Guide, 1st Printing
USA
(fus)
Roadside Emergencies
235
The fuses are coded as follows.
Fuse/Relay
Location
Fuse Amp
Rating
Protected Circuits
1
30A
Driver smart window motor
2
15A
Brake on/off switch, Center
high-mounted stop lamp
3
15A
Not used (Spare)
4
30A
Not used (Spare)
5
10A
Keypad illumination, Brake shift
interlock
6
20A
Turn signal lamps
7
10A
Low beam headlamps (left)
8
10A
Low beam headlamps (right)
9
15A
Courtesy lamps
10
15A
Backlighting, Puddle lamps
2010 Milan
(mln)
Owners Guide, 1st Printing
USA
(fus)
Roadside Emergencies
236
Fuse/Relay
Location
Fuse Amp
Rating
Protected Circuits
11
10A
AWD module
12
7.5A
Power outside mirrors
13
5A
SYNC module
14
10A
Electronic Finish Panel (EFP)
radio and climate control buttons
module, Navigation display, Center
Information Display, GPS module
15
10A
Climate control
16
15A
Not used (Spare)
17
20A
Door locks, Trunk release
18
20A
Heated seats
19
25A
Amplifier
20
15A
On-Board Diagnostic connector
21
15A
Fog lamps
22
15A
Front sidemarker lamps, Park
lamps, License plate lamp
23
15A
High beam headlamps
24
20A
Horn
25
10A
Demand lamps/power saver relay
26
10A
Instrument cluster battery power
27
20A
Ignition switch
28
5A
Radio crank sense circuit
29
5A
Instrument cluster ignition power
30
5A
Not used (Spare)
31
10A
Not used (Spare)
32
10A
Restraint control module
33
10A
Not used (Spare)
34
5A
Not used (Spare)
35
10A
Rear park assist, Blind spot
monitor system, Heated seats,
AWD, Rear video camera
2010 Milan
(mln)
Owners Guide, 1st Printing
USA
(fus)
Roadside Emergencies
237
Fuse/Relay
Location
Fuse Amp
Rating
Protected Circuits
36
5A
Passive Anti-Theft Sensor (PATS)
transceiver
37
10A
Not used (Spare)
38
20A
Subwoofer amplifier
39
20A
Radio
40
20A
Not used (Spare)
41
15A
Automatic dimming mirror, Moon
roof, Compass, Ambient lighting
42
10A
Electronic stability control,
Electronic power assist steering
43
10A
Not used (Spare)
44
10A
Fuel diode/Powertrain control
module
45
5A
Heated backlight and blower relay
coil, Wiper washer
46
7.5A
Occupant Classification Sensor
(OCS) module, Passenger airbag
off lamp
47
30A Circuit
Breaker
Power windows
48
Delayed accessory relay
Power distribution box
The power distribution box is located in the engine compartment. The
power distribution box contains high-current fuses that protect your
vehicle’s main electrical systems from overloads.
WARNING:
Always disconnect the battery before servicing high
current fuses.
WARNING:
To reduce risk of electrical shock, always replace
the cover to the Power Distribution Box before reconnecting the
battery or refilling fluid reservoirs.
2010 Milan
(mln)
Owners Guide, 1st Printing
USA
(fus)
Roadside Emergencies
238
If the battery has been disconnected and reconnected, refer to the
Battery
section of the
Maintenance and Specifications
chapter.
The high-current fuses are coded as follows.
Fuse/Relay
Location
Fuse Amp
Rating
Protected Circuits
1
50A*
Electronic power assist steering
B+
2
50A*
Electronic power assist steering
B+
3
40A*
Powertrain control module (PCM)
(relay 57 power)
4
Not used
5
30A*
Starter motor (relay 55 power)
6
40A*
Rear defrost (relay 53 power)
7
Not used
8
40A*
Anti-lock Braking System (ABS)
pump
9
20A*
Wipers washer
10
30A*
ABS valve
11
Not used
2010 Milan
(mln)
Owners Guide, 1st Printing
USA
(fus)
Roadside Emergencies
239
Fuse/Relay
Location
Fuse Amp
Rating
Protected Circuits
12
Not used
13
Not used
14
Not used
15
Not used
16
Not used
17
10A**
Alternator
18
Not used
19
Not used
20
Not used
21
Not used
22
20A*
Console power point
23
10A**
PCM – Keep alive power, Canister
vent
24
Not used
25
10A**
A/C clutch (relay 43 power)
26
15A**
Left headlamp (relay 42 power)
27
15A**
Right headlamp (relay 44 power)
28
60A*
Cooling fan motor
29
20A*
Front power point
30
30A*
Fuel relay (relay 54 power)
31
30A*
Passenger power seat
32
30A*
Driver power seat
33
20A*
Moon roof motor power feed
34
Not used
35
40A*
Front A/C blower motor (relay 52
power)
36
1A Diode
Fuel pump
37
1A Diode
One-touch start
38
10A**
Heated side mirrors
39
Not used
40
Not used
2010 Milan
(mln)
Owners Guide, 1st Printing
USA
(fus)
Roadside Emergencies
240
Fuse/Relay
Location
Fuse Amp
Rating
Protected Circuits
41
G8VA relay
Backup lamps
42
G8VA relay
Left headlamps
43
G8VA relay
A/C clutch
44
G8VA relay
Right headlamps
45
15A**
Injectors
46
15A**
PCM
47
10A**
General powertrain components,
A/C clutch relay, Back-up lamps
48
15A**
Ignition coils
49
15A**
Emissions related powertrain
components (2.5L)
20A**
Emissions related powertrain
components (3.0L)
50
Not used
51
Not used
52
Full ISO relay
Blower motor relay
53
Full ISO relay
Rear defrost relay
54
Full ISO relay
Fuel relay
55
Full ISO relay
Starter relay
56
Not used
57
Full ISO relay
PCM relay
58
Not used
* Cartridge Fuses ** Mini Fuses
CHANGING THE TIRES
If you get a flat tire while driving, do not apply the brake heavily.
Instead, gradually decrease your speed. Hold the steering wheel firmly
and slowly move to a safe place on the side of the road.
Note:
The tire pressure monitoring system (TPMS) indicator light will
illuminate when the spare tire is in use. To restore the full functionality
of the monitoring system, all road wheels equipped with tire pressure
monitoring sensors must be mounted on the vehicle.
2010 Milan
(mln)
Owners Guide, 1st Printing
USA
(fus)
Roadside Emergencies
241