Ford Freestar - 2007 Fuse Box Diagram

Ford Freestar - 2007 Fuse Box Diagram

desirable to prevent power operation of the door by rear seat passengers
or if manual operation of the door is desired or necessary when the
vehicle is stopped or parked on a steep downhill grade.
Refer to the
Manual operation of the sliding door
section in this
chapter for more information.
With the child safety lock engaged, the inside handle operation will
always be disabled regardless of the position of the Power Door Lockout
control. Refer to the
Sliding door child safety lock
section in this
chapter for more information. The trim mounted rear seat control and
the outside handle remain functional for power operation.
Safety/Obstructions
If anything obstructs the Power Sliding Door while it is power closing or
opening, the door will automatically reverse or stop depending on the
position of the door, provided it meets sufficient resistance.
Resetting the PSD
The power sliding door may operate incorrectly or not at all because of
the following conditions:
a low voltage or dead battery
the door is left opened for more than 6 hours
the battery is disconnected
the PSD Passenger compartment fuse panel fuse (fuse #11) is
removed or blown. Refer to
Fuses and relays
in the
Roadside
Emergencies
chapter.
If any of the above conditions has occurred, perform the following steps
to reset the PSD so that electronics can relearn the open and closed
positions:
1. Check to see if PSD is securely closed.
2. Make sure the gearshift is in (P) Park.
3. Push the PSD control on the overhead console to open the door.
4. Wait five (5) seconds and close the door by pressing the PSD control
on the overhead console.
5. Wait five (5) seconds and repeat Steps 3 and 4 then go on to Step 6.
6. Repeat Steps 3–5 for opposite door.
If the door still does not operate correctly:
7. Ensure the ignition is in the OFF position
2007 Freestar
(win)
Owners Guide (post-2002-fmt)
USA
(fus)
Driver Controls
64
8. Remove the PSD fuse (fuse #11) from the passenger fuse panel and
leave it out for thirty (30) seconds. Refer to the chapter on Fuses and
Relays. Refer to
Fuses and relays
in the
Roadside emergencies
chapter.
9. Reinstall the fuse and wait ten (10) seconds.
10. Repeat Steps 1–6 above.
If the door still does not operate correctly, see your dealer for service.
Sliding Door Child Safety Lock
Your vehicle is equipped with a sliding door child safety lock that helps
prevent passengers from operating the sliding door by using the inside
door handle, refer to the
Childproof door locks
in the
Locks and
security
chapter.
To open the sliding door when the
child safety lock is on:
Unlock the sliding door and open
the door from the outside.
Press the right or left hand
control on the overhead console
or the remote to open the door.
The second row passenger switch will still be functional to open the
door. To prevent the second row passenger from operating the PSD,
turn the Power Door Lockout control to the OFF position.
CENTER CONSOLE (IF EQUIPPED)
Your vehicle may be equipped with a utility compartment.
INSTRUMENT PANEL STORAGE COMPARTMENT
The storage compartment may be
used to secure sunglasses or similar
sized objects. Press the control to
open the storage compartment.
2007 Freestar
(win)
Owners Guide (post-2002-fmt)
USA
(fus)
Driver Controls
65
CLOCK (IF EQUIPPED)
Press the right (+) control to move
the time display forwards.
Press the left (-) control to move
the time display backwards.
AUXILIARY POWER POINT (12VDC)
Power outlets are designed for accessory plugs only. Do not insert
any other object in the power outlet as this will damage the
outlet and blow the fuse. Do not hang any type of accessory or
accessory bracket from the plug. Improper use of the power
outlet can cause damage not covered by your warranty.
Do not use the power point for operating the cigarette lighter element (if
equipped).
To prevent the fuse from being blown, do not use the power point(s)
over the vehicle capacity of 12 VDC/180W.
To prevent the battery from being discharged, do not use the power
point longer than necessary when the engine is not running.
Always keep the power point caps closed when not being used.
There are up to three auxiliary power points in the following locations:
Located on the instrument panel.
2007 Freestar
(win)
Owners Guide (post-2002-fmt)
USA
(fus)
Driver Controls
66
open and close the right and left power sliding doors (if equipped).
recall memory seat/side view mirrors/adjustable pedals position Driver
1 or Driver 2 (if equipped).
The keypad can be operated with the factory set 5–digit entry code; this
code is located:
on the owner’s wallet card in the glove box,
marked on the passenger compartment fuse panel (located below and
to the left of the steering, near the brake pedal),
and is available from your
authorized dealer.
You can also create your own 5–digit
personal entry code.
When pressing the controls on the
keypad, press the middle of the
controls to ensure a good activation.
Programming a personal entry
code
To create your own personal entry code(s):
1. Enter the factory set code.
Note:
The driver’s door will unlock.
2. Within five seconds press and release the 1
2 on the keypad.
Note:
The lock motors will cycle, locked then unlocked.
3. Enter your personal 5-digit code. Each number must be entered
within five seconds of each other.
4. Enter a sixth digit if you wish to have the personal entry code recall
memory position Driver 1 or Driver 2 (if equipped with the memory
seat/side view mirrors/adjustable pedals feature).
Note:
The lock motors
will cycle, locked then unlocked.
Press 1
2 to recall the Driver 1 position.
Press 3
4 to recall the Driver 2 position.
5. After five seconds of keypad inactivity, programming mode is exited.
All of the vehicle doors will lock and unlock to confirm the code has
been stored. Each memory feature driver position (Driver 1 or Driver 2)
can be associated with only one personal code. The factory-set code
cannot be associated with a memory recall position.
You can program up to three personal codes; these codes do not replace
the factory-set code.
2007 Freestar
(win)
Owners Guide (post-2002-fmt)
USA
(fus)
Locks and Security
107
Always transport children 12 years old and under in the back
seat and always properly use appropriate child restraints.
The National Highway Traffic Safety Administration (NHTSA)
recommends a minimum distance of at least 10 inches (25 cm)
between an occupant’s chest and the driver airbag module.
Never place your arm over the airbag module as a deploying
airbag can result in serious arm fractures or other injuries.
To properly position yourself away from the airbag:
Move your seat to the rear as far as you can while still reaching the
pedals comfortably.
Recline the seat slightly one or two degrees from the upright position.
Do not put anything on or over the airbag module. Placing
objects on or over the airbag inflation area may cause those
objects to be propelled by the airbag into your face and torso causing
serious injury.
Do not attempt to service, repair, or modify the airbag
supplemental restraint systems or its fuses. See your authorized
dealer.
Modifying or adding equipment to the front end of the vehicle
(including frame, bumper, front end body structure and tow
hooks) may affect the performance of the airbag system, increasing the
risk of injury. Do not modify the front end of the vehicle.
2007 Freestar
(win)
Owners Guide (post-2002-fmt)
USA
(fus)
Seating and Safety Restraints
154
A difficulty with the system is indicated by one or more of the following:
The readiness light (same light
for front and side airbag system)
will either flash or stay lit.
The readiness light will not
illuminate immediately after ignition is turned on.
A series of five beeps will be heard. The tone pattern will repeat
periodically until the problem and/or light are repaired.
If any of these things happen, even intermittently, have the supplemental
restraint system serviced at an authorized dealer immediately. Unless
serviced, the system may not function properly in the event of a
collision.
Seat-mounted side airbag system (if equipped)
Do not place objects or mount equipment on or near the airbag
cover on the side of the seatbacks of the front seats or in front
seat areas that may come into contact with a deploying airbag. Failure
to follow these instructions may increase the risk of personal injury in
the event of a collision.
Do not use accessory seat covers. The use of accessory seat
covers may prevent the deployment of the side airbags and
increase the risk of injury in an accident.
Do not lean your head on the door. The side airbag could injure
you as it deploys from the side of the seatback.
Do not attempt to service, repair, or modify the airbag SRS, its
fuses or the seat cover on a seat containing an airbag. See your
authorized dealer.
All occupants of the vehicle should always wear their safety belts
even when an airbag SRS is provided.
2007 Freestar
(win)
Owners Guide (post-2002-fmt)
USA
(fus)
Seating and Safety Restraints
162
Do not attempt to service, repair, or modify the Safety Canopy
²
system, its fuses, the A, B, C or D pillar trim, or the headliner on
a vehicle containing a Safety Canopy
²
. See your authorized dealer.
All occupants of the vehicle including the driver should always
wear their safety belts even when an airbag SRS and Safety
Canopy
²
system is provided.
To reduce risk of injury, do not obstruct or place objects in the
deployment path of the inflatable Safety Canopy
²
.
How does the Safety Canopy
´
system work?
The design and development of the
Safety Canopy
²
system included
recommended testing procedures
that were developed by a group of
automotive safety experts known as
the Side Airbag Technical Working
Group. These recommended testing
procedures help reduce the risk of
injuries related to the deployment of
side airbags (including the Safety
Canopy
²
).
The Safety Canopy
²
system
consists of the following:
An inflatable nylon curtain with a
gas generator concealed behind
the headliner and above the doors
(one on each side of vehicle).
A headliner designed to flex open above the side doors to allow Safety
Canopy
²
deployment.
The same readiness airbag light, electronic control and diagnostic unit
as used for the front airbags.
Two crash sensors mounted under the front seats (one on each side).
2007 Freestar
(win)
Owners Guide (post-2002-fmt)
USA
(fus)
Seating and Safety Restraints
165
1400 – (2 x 220) – (9 x 100) = 1400 – 440 – 900 = 60 lb. Now you
have the load capacity to transport the cement and your friend home.
In metric units, the calculation would be: 635 kg — (2 x 99 kg) —
(9 x 45 kg) = 635 — 198 — 405 = 32 kg.
The above calculations also assume that the loads are positioned in your
vehicle in a manner that does not overload the Front or the Rear Gross
Axle Weight Rating specified for your vehicle on the Safety Compliance
Certification Label found on the edge of the driver’s door.
TRAILER TOWING
Your vehicle is capable either of towing Class I trailers or up to Class II
trailers when equipped with the optional trailer tow package.
If your vehicle does not have the optional trailer tow package your
vehicle is partially prepped for trailer tow lamp wiring but you will also
need to install electrical kit (15A416). This kit contains fuses and relays
to isolate the vehicle lighting circuitry from the trailer lighting and an
adapter wiring harness containing the standard 4-pin trailer plug. Refer
to the
Trailer lamps
section in this chapter for additional information.
Do not tow above 2,000 lb. (907 kg) without the
manufacturer-installed trailer tow package.
A new underbody wiring harness (14406) will be a component to this kit
and will need to be installed, if applicable, per instructions located in the
service kit.
If your vehicle has the optional trailer tow package it comes with heavy
duty cooling fans, auxiliary transmission fluid cooler, an auxiliary engine
oil cooler (4.2L engine only), heavy duty battery, trailer tow wiring
(including fuses and relays to isolate the vehicle lighting circuitry from
the trailer lighting) and a kit (in a cardboard box) that includes an
adapter wiring harness that contains the standard 4-pin trailer plug.
Trailer towing puts additional loads on your vehicle’s engine,
transmission, axle, brakes, tires, and suspension. For your safety and to
maximize vehicle performance, be sure to use the proper equipment
while towing.
Follow these guidelines to ensure safe towing procedure:
Stay within your vehicle’s load limits. If exceeded, cargo should be
removed from the trailer and/or the vehicle until all weights are within
specified limits.
Thoroughly prepare your vehicle for towing. Refer to
Preparing to
tow
in this chapter.
2007 Freestar
(win)
Owners Guide (post-2002-fmt)
USA
(fus)
Tires, Wheels and Loading
206
When the key is in the ignition and in the 3 (OFF) position, the
automatic transmission shift lever can be moved from the P (Park)
position without the brake pedal depressed. To avoid unwanted vehicle
movement, always set the parking brake.
3. Start the vehicle.
If it is necessary to use the above procedure to move the gearshift lever,
it is possible that a fuse has blown or the vehicle’s brakelamps are not
operating properly. Refer to
Fuses and relays
in the
Roadside
Emergencies
chapter.
Do not drive your vehicle until you verify that the brakelamps
are working.
Always set the parking brake fully and make sure the gearshift is
latched in P (Park). Turn the ignition to the LOCK position and
remove the key whenever you leave your vehicle.
If the parking brake is fully released, but the brake warning lamp
remains illuminated, the brakes may not be working properly.
See your authorized dealer.
Driving with an automatic overdrive transaxle with column
gearshift
Your transaxle is equipped with an adaptive learning strategy found in
the vehicle computer. This feature is designed to increase durability and
provide consistent shift feel over the life of the vehicle. A new vehicle or
transaxle may have firm and/or soft shifts. This operation is considered
normal and will not affect function or durability of the transaxle. Over
time, the adaptive learning process will fully update transaxle operation.
Additionally, whenever the battery is disconnected or a new battery
installed, the strategy must be relearned.
Your automatic overdrive transaxle provides fully automatic operation in
either D (Drive) or 3. Driving with the gearshift lever in D (Drive) gives
the best fuel economy for normal driving conditions. For manual control
start in 1 (First) and then shift manually.
To put your vehicle in gear, start the engine, depress the brake pedal,
then move gearshift lever out of P (Park). Once you place the gearshift
lever securely into position, gradually release the brake pedal and use
the accelerator as necessary.
2007 Freestar
(win)
Owners Guide (post-2002-fmt)
USA
(fus)
Driving
220
flash. Press the flasher control again to turn them off. Use it when your
vehicle is disabled and is creating a safety hazard for other motorists.
Note:
With extended use, the flasher may run down your battery.
FUEL PUMP SHUT-OFF SWITCH
This device stops the electric fuel pump from sending fuel to the engine
when your vehicle has had a substantial jolt.
After an accident, if the engine cranks but does not start, this switch
may have been activated.
This switch is located behind the
service panel on the right side of
the cargo area.
To reset the switch:
1. Turn the ignition OFF.
2. Check the fuel system for leaks.
3. If no leaks are apparent, reset the
switch by pushing in on the reset
button.
4. Turn the ignition ON.
5. Wait a few seconds and return
the key to OFF.
6. Make another check for leaks.
FUSES AND RELAYS
Fuses
If electrical components in the
vehicle are not working, a fuse may
have blown. Blown fuses are
identified by a broken wire within
the fuse. Check the appropriate
fuses before replacing any electrical
components.
15
2007 Freestar
(win)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
227
Note:
Always replace a fuse with one that has the specified amperage
rating. Using a fuse with a higher amperage rating can cause severe wire
damage and could start a fire.
Standard fuse amperage rating and color
COLOR
Fuse
rating
Mini
fuses
Standard
fuses
Maxi
fuses
Cartridge
maxi
fuses
Fuse link
cartridge
2A
Grey
Grey
3A
Violet
Violet
4A
Pink
Pink
5A
Tan
Tan
7.5A
Brown
Brown
10A
Red
Red
15A
Blue
Blue
20A
Yellow
Yellow
Yellow
Blue
Blue
25A
Natural
Natural
30A
Green
Green
Green
Pink
Pink
40A
Orange
Green
Green
50A
Red
Red
Red
60A
Blue
Yellow
70A
Tan
Brown
80A
Natural
Black
Passenger compartment fuse panel
The fuse panel is located below and to the left of the steering wheel by
the brake pedal. Remove the panel cover to access the fuses. To remove
the fuse panel cover, pull up on the latch on the right or left side of the
cover.
To remove a fuse use the fuse puller tool provided on the fuse panel
cover.
2007 Freestar
(win)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
228
The fuses are coded as follows:
Fuse/Relay
Location
Fuse Amp
Rating
Passenger Compartment Fuse
Panel Description
1
Relay
Accessory delay relay 1
2
Relay
Accessory delay relay 2
3
10A
Front wiper motor Run feed
4
5A
B+ feed to outside mirrors
5
20A
Vent window power feed/Radio
feed
6
5A
Driver door switch
illumination/Passenger door
switch illumination
7
10A
Rear wiper Run feed
8
10A
Cluster/Electronic Automatic
Temperature Control (EATC) B+
feed, DVD
9
10A
Passive Anti-theft System (PATS)
LED feed
10
5A
Auxiliary radio
11
5A
Auxiliary climate control
system/Power Liftgate
Module/Left and right power
sliding door module/Data Link
Connector (DLC)/Clock B+ feeds
2007 Freestar
(win)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
229
Fuse/Relay
Location
Fuse Amp
Rating
Passenger Compartment Fuse
Panel Description
12
5A
Brake-Shift Interlock (BSI) Run
feed, Climate control system Run
feed
13
5A
Compass/Driver heated
seat/Passenger heated
seats/Reverse sensing
system/Power Liftgate
Module/Power sliding door Run
feeds
14
5A
Underhood fuse box Run feed,
Front blower Run feed
15
10A
Brake On-Off (BOO) switch B+
16
5A
Steering angle/Cluster/Power
sliding door and power liftgate
inhibit LED/Electrochromatic
mirror Run/Start/Tire Pressure
Monitoring System (TPMS)
17
10A
Restraint Control Module
(RCM)/Passenger Air bag Disable
Indicator (PADI)/Passenger
Occupant Detection System
(PODS) Run/Start
18
10A
Anti-lock Brake System (ABS)
module/Brake pressure
switch/Speed control Run/Start
19
5A
PATS/Cluster/Air bag
LED/Powertrain Control Module
(PCM) relay Run/Start
20
10A
Liftgate Start feed, Radio Start
feed
21
10A
Starter relay power START
2007 Freestar
(win)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
230
Power distribution box
The power distribution box is located in the engine compartment. The
power distribution box contains high-current fuses that protect your
vehicle’s main electrical systems from overloads.
Always disconnect the battery before servicing high current
fuses.
To reduce risk of electrical shock, always replace the cover to
the Power Distribution Box before reconnecting the battery or
refilling fluid reservoirs.
If the battery has been disconnected and reconnected, refer to the
Battery
section of the
Maintenance and Specifications
chapter.
To remove the cover of the power distribution box, pull the release
latches at both ends of the cover, then pull the cover up.
The high-current fuses are coded as follows:
Fuse/Relay
Location
Fuse Amp
Rating
Power Distribution Box
Description
1
Not used
2
30A**
Right cooling fan
2007 Freestar
(win)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
231
Fuse/Relay
Location
Fuse Amp
Rating
Power Distribution Box
Description
3
30A**
Left cooling fan
4
30A**
Starter solenoid
5
30A**
Right-hand power sliding door
6
30A**
SJB accessory #2 (driver power
window)
7
30A**
Auxiliary blower motor
8
40A**
Anti-lock Brake System (ABS) #2
(coil power)
9
30A**
Power liftgate
10
30A**
SJB accessory #1 (passenger
window, radio, vent windows)
11
30A**
Left power seat/heated seat
12
40A**
ABS #1 (pump motor)
13
40A**
Rear defroster
14
30A**
Front climate control system
blower motor
15
30A**
Right power seat/heated seat
16
30A**
Left-hand power sliding door
20
Mini relay
Powertrain Control Module (PCM)
power
21
Mini relay
Horn
22
Micro relay
A/C clutch
23
Micro relay
High beams
24
Mini relay
Starter
25
Micro relay
Fuel pump
26
Not used
27
Not used
28
Mini relay
Auxiliary blower
29
Micro relay
Trailer park lamps
30
Micro relay
Left trailer stop/turn lamps
31
Micro relay
Right trailer stop/turn lamps
32
Mini relay
Rear defroster
2007 Freestar
(win)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
232
Fuse/Relay
Location
Fuse Amp
Rating
Power Distribution Box
Description
40
15A*
Engine #1 (A/C relay coil, IMRC,
HEGO sensors, Canister purge,
Transmission module)
41
25A*
Horn
42
10A*
A/C clutch
43
15A*
Engine #2 (Cooling fan relays,
Injectors, PCM, MAF sensor, IAC,
Ignition coil, ESM)
44
10A*
Heated PCV
45
15A*
High beams
46
20A*
Trailer stop/turn lamps
47
15A*
Fuel pump, Fuel pump shut-off
switch
48
Not used
49
10A*
PCM KAP, Canister vent
50
10A*
Alternator
51
10A*
Adjustable pedals (non-memory)
or memory module
52
20A*
Trailer tow park lamps
53
10A*
Heated mirrors
54
30A*
Front wiper motor
55
25A*
Rear wiper motor
56
30A*
Premium sound radio
57
Not used
58
30A*
SJB #1 – Center High-Mounted
Stop Lamp (CHMSL), License
plate lamps, OBD II, Dome lamp,
Auxiliary blend doors, Switch
illumination (feeds F–8, F–9, F–10
and F–11)
59
20A*
Radio (non-premium)
60
30A*
SJB #4 – Back-up lamps, Door
locks
2007 Freestar
(win)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
233
Fuse/Relay
Location
Fuse Amp
Rating
Power Distribution Box
Description
61
Not used
62
30A*
SJB #3 – Right cornering/auxiliary
lamps, Right low beam, Left front
park/turn lamps, Left rear
park/stop/turn lamps, Instrument
panel courtesy lamps, Step well
lamps, Left signal mirror, Clock,
Cluster, Message center (SJB
F–15), Switch illumination for:
overhead console, DVD/Rear
climate control system, Headlamp
switch illumination, Climate
control illumination
63
20A*
Instrument panel power point,
Cigar lighter
64
20A*
Ignition switch #1 feed
65
30A*
SJB #2 – Left cornering/auxiliary
lamps, Left low beam, Right front
park/turn lamps, Right rear
park/stop/turn lamps, Puddle
lamps, Mirror signals, Visors, 2nd
and 3rd row lamps, Cargo lamp,
Defroster indicator
66
20A*
2nd and 3rd row seat power
points
67
20A*
Ignition switch #2 feed
70
Not used
71
Not used
72
Not used
73
Not used
74
Not used
75
Diode
PCM
76
Diode
A/C clutch
* Mini Fuse ** Cartridge Fuse
2007 Freestar
(win)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
234
Auxiliary relay box (cooling fans)
The relay box is located in the engine compartment by the radiator.
Fuse/Relay
location
Fuse amp
rating
Description
1
Cooling fan relay #4
2
Cooling fan relay #5
3
Cooling fan relay #3
4
Cooling fan relay #1
5
Cooling fan relay #2
6
40A*
Right-hand cooling fan motor (Vehicles with
trailer tow package only)
7
15A**
Low-speed cooling fan circuit breaker
(Vehicles with trailer tow package only)
8
40A*
Left-hand cooling fan motor (Vehicles with
trailer tow package)
10A**
Low-speed cooling fan circuit breaker
(Vehicles without trailer tow package)
* Maxi fuse **Circuit breaker
CHANGING A FLAT TIRE
If you get a flat tire while driving:
do not brake heavily.
gradually decrease the vehicle’s speed.
hold the steering wheel firmly.
slowly move to a safe place on the side of the road.
If your low tire warning light is on, refer to
Low tire warning
in this
chapter.
2007 Freestar
(win)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
235