Ford Flex - 2009 Fuse Box Diagram

Ford Flex - 2009 Fuse Box Diagram

Refrigerator:
Press the COOL side
of the control and the indicator light
on the cool side of the switch will
glow when the refrigerator is active.
When in cool mode the temperature
will cool to approximately 41°F
(5°C). Press COOL again to turn off
the refrigerator or press FREEZE to
switch over to freezer mode.
Freezer:
Press the FREEZE side of
the control and the indicator light
on the freeze side of the switch will
glow when the freezer is active.
When in freeze mode the
temperature will cool to
approximately 23°F (-5°C). Press
FREEZE again to turn off the
freezer or press COOL to switch
over to refrigerator mode.
When the vehicle is turned off, the refrigerator/freezer will also turn off
and will turn back on to the last used mode (freeze or cool) once the
vehicle is restarted.
Cleaning and maintenance
The refrigerator/freezer is maintenance free, but you can clean the inside
of the unit and the cover with a mild soap and water solution when
needed.
Note:
Under certain conditions, condensation on the inside walls of the
refrigerator is normal.
AUXILIARY POWER POINT (12VDC)
Power outlets are designed for accessory plugs only. Do not insert
any other object in the power outlet as this will damage the
outlet and blow the fuse. Do not hang any type of accessory or
accessory bracket from the plug. Improper use of the power
outlet can cause damage not covered by your warranty.
2009 Flex
(471)
Owners Guide (post-2002-fmt)
USA
(fus)
Driver Controls
93
An auxiliary power point is located
by the passenger’s ankle near the
floor in the front console bin. A
second one is located in the center
console utility compartment.
A third rear auxiliary power point is
located on the rear of the center
console which is accessible from the
second row seat.
A fourth auxiliary power point is
located on the right trim panel in
the rear cargo area.
Do not use the power point for
operating the cigarette lighter
element (if equipped).
To prevent the fuse from being
blown, do not use the power
point(s) over the vehicle capacity of
12 VDC/180W. If the power point or
cigar lighter socket is not working, a fuse may have blown. Refer to
Fuses and relays
in the
Roadside Emergencies
chapter for information
on checking and replacing fuses.
To have full capacity usage of your power point, the engine is required to
be running to avoid unintentional discharge of the battery. To prevent
the battery from being discharged:
do not use the power point longer than necessary when the engine is
not running,
2009 Flex
(471)
Owners Guide (post-2002-fmt)
USA
(fus)
Driver Controls
94
To properly position yourself away from the airbag:
Move your seat to the rear as far as you can while still reaching the
pedals comfortably.
Recline the seat slightly one or two degrees from the upright position.
WARNING:
Do not put anything on or over the air bag module.
Placing objects on or over the air bag inflation area may cause
those objects to be propelled by the air bag into your face and torso
causing serious injury.
WARNING:
Do not attempt to service, repair, or modify the
airbag supplemental restraint systems or its fuses. See your
authorized dealer.
WARNING:
Modifying or adding equipment to the front end of
the vehicle (including frame, bumper, front end body structure
and tow hooks) may affect the performance of the airbag system,
increasing the risk of injury. Do not modify the front end of the
vehicle.
Children and airbags
Children must always be properly
restrained. Accident statistics
suggest that children are safer when
properly restrained in the rear
seating positions than in the front
seating position. Failure to follow
these instructions may increase the
risk of injury in a collision.
WARNING:
Airbags can kill
or injure a child in a child
seat.
NEVER
place a rear-facing
child seat in front of an active
airbag. If you must use a
forward-facing child seat in the
front seat, move the seat all the
way back.
2009 Flex
(471)
Owners Guide (post-2002-fmt)
USA
(fus)
Seating and Safety Restraints
183
WARNING:
Do not attempt to service, repair, or modify the
airbag SRS, its fuses or the seat cover on a seat containing an
airbag. See your authorized dealer.
WARNING:
All occupants of the vehicle should always wear
their safety belts even when an airbag SRS is provided.
How does the side airbag system work?
The design and development of the side airbag system included
recommended testing procedures that were developed by a group of
automotive safety experts known as the Side Airbag Technical Working
Group. These recommended testing procedures help reduce the risk of
injuries related to the deployment of side airbags.
The side airbag system consists of
the following:
An inflatable nylon bag (airbag)
with a gas generator concealed
behind the outboard bolster of
the driver and front passenger
seatbacks.
A special seat cover designed to
allow airbag deployment.
The same warning light,
electronic control and diagnostic
unit as used for the front airbags.
Crash sensors located on the B
and C pillars (one sensor on each
pillar on each side of the vehicle).
Side airbags, in combination with
safety belts, can help reduce the risk of severe injuries in the event of a
significant side impact collision.
The side airbags are fitted on the outboard side of the seatbacks of the
front seats. In certain lateral collisions, the airbag on the side affected by
the collision will be inflated. If the front passenger sensing system
detects an empty seat, the front passenger seat-mounted side airbag will
be deactivated. The airbag was designed to inflate between the door
panel and occupant to further enhance the protection provided
occupants in side impact collisions.
2009 Flex
(471)
Owners Guide (post-2002-fmt)
USA
(fus)
Seating and Safety Restraints
191
WARNING:
Do not lean your head on the door. The Safety
Canopy™ could injure you as it deploys from the headliner.
WARNING:
Do not attempt to service, repair, or modify the
Safety Canopy™ system, its fuses, the A, B, C or D pillar trim, or
the headliner on a vehicle containing a Safety Canopy™. See your
authorized dealer.
WARNING:
All occupants of the vehicle including the driver
should always wear their safety belts even when an airbag SRS
and Safety Canopy™ system is provided.
WARNING:
To reduce risk of injury, do not obstruct or place
objects in the deployment path of the inflatable Safety Canopy™.
2009 Flex
(471)
Owners Guide (post-2002-fmt)
USA
(fus)
Seating and Safety Restraints
193
If you cannot move the gearshift lever out of P (Park) with ignition in
the on position and the brake pedal depressed:
1. Apply the parking brake, turn
ignition key to off, then remove the
key.
2. Using a screwdriver (or similar
tool), remove the protective cover
to the interlock release access hole
on the console.
3. Insert the screwdriver (or similar
tool) into the access hole and press
downward while pulling the
gearshift lever out of the P (Park)
position and into the N (Neutral)
position.
4. Remove the tool and reinstall the
protective cover.
5. Start the vehicle and release the
parking brake.
If it is necessary to use the above procedure to move the gearshift lever,
it is possible that a fuse has blown or the vehicle’s brakelamps are not
operating properly. Refer to
Fuses and relays
in the
Roadside
Emergencies
chapter.
WARNING:
Do not drive your vehicle until you verify that the
brakelamps are working.
WARNING:
Always set the parking brake fully and make sure
the gearshift is latched in P (Park). Turn the ignition to the off
position and remove the key whenever you leave your vehicle.
WARNING:
If the parking brake is fully released, but the brake
warning lamp remains illuminated, the brakes may not be
working properly. See your authorized dealer as soon as possible.
2009 Flex
(471)
Owners Guide (post-2002-fmt)
USA
(fus)
Driving
263
FUEL PUMP SHUT-OFF
In the event of a moderate to severe collision, this vehicle is equipped
with a fuel pump shut-off feature that stops the flow of fuel to the
engine. Not every impact will cause a shut-off.
Should your vehicle shut off after a collision due to this feature, you may
restart your vehicle by doing the following:
1. Turn the ignition switch to the off position.
2. Turn the ignition switch to the on position.
In some instances the vehicle may not restart the first time you try to
restart and may take one additional attempt.
WARNING:
Failure to inspect and if necessary repair fuel leaks
after a collision may increase the risk of fire and serious injury.
Ford Motor Company recommends that the fuel system be inspected
by an authorized dealer after any collision.
FUSES AND RELAYS
Fuses
If electrical components in the
vehicle are not working, a fuse may
have blown. Blown fuses are
identified by a broken wire within
the fuse. Check the appropriate
fuses before replacing any electrical
components.
Note:
Always replace a fuse with one that has the specified amperage
rating. Using a fuse with a higher amperage rating can cause severe wire
damage and could start a fire.
15
2009 Flex
(471)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
280
Standard fuse amperage rating and color
COLOR
Fuse
rating
Mini
fuses
Standard
fuses
Maxi
fuses
Cartridge
maxi
fuses
Fuse link
cartridge
2A
Grey
Grey
3A
Violet
Violet
4A
Pink
Pink
5A
Tan
Tan
7.5A
Brown
Brown
10A
Red
Red
15A
Blue
Blue
20A
Yellow
Yellow
Yellow
Blue
Blue
25A
Natural
Natural
30A
Green
Green
Green
Pink
Pink
40A
Orange
Green
Green
50A
Red
Red
Red
60A
Blue
Yellow
Yellow
70A
Tan
Brown
80A
Natural
Black
Black
2009 Flex
(471)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
281
Passenger compartment fuse panel
The fuse panel is located under the instrument panel to the left of the
steering wheel.
The fuses are coded as follows.
Fuse/Relay
Location
Fuse Amp
Rating
Protected Circuits
1
30A
Driver smart window motor
2
15A
Not used (spare)
3
15A
Family entertainment system
(FES)
4
30A
DC/AC inverter
5
10A
Passenger compartment fuse
panel logic power, Keypad
illumination, BTSI
6
20A
Turn signals
7
10A
Low beam headlamps (left)
2009 Flex
(471)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
282
Fuse/Relay
Location
Fuse Amp
Rating
Protected Circuits
8
10A
Low beam headlamps (right)
9
15A
Interior lights, Cargo lamps
10
15A
Backlighting, Puddle lamps
11
10A
All wheel drive
12
7.5A
Not used (spare)
13
5A
Keypad, Mirror switch, Memory
module, DSM logic, Adjustable
pedals
14
10A
Power liftgate module, CID, MGM
15
10A
Climate control head
16
15A
EFP, Navigation Screen
17
20A
All power lock motor feeds,
Liftgate release
18
20A
2nd row power seat, Front heated
seats
19
25A
Moon roof
20
15A
OBDII connector, Memory seat
21
15A
Fog lamps
22
15A
Park lamps, License lamps
23
15A
High beam headlamps
24
20A
Horn relay
25
10A
Demand lamps/Interior lamps,
Power fold seat (2nd row)
26
10A
Instrument panel cluster
27
20A
Ignition Switch
28
5A
Radio, Radio start signal
29
5A
Instrument panel cluster
30
5A
Overdrive cancel and grade assist
switch
31
10A
Not used (spare)
32
10A
Restraint control module
33
10A
Battery charge relay
2009 Flex
(471)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
283
Fuse/Relay
Location
Fuse Amp
Rating
Protected Circuits
34
5A
Yaw rate sensor, ABS R/S,
Refrigerator relay coil
35
10A
Steering rotation sensor, Rear
park assist, Heated seat modules,
AWD, DC/AC inverter
36
5A
PATS module
37
10A
Not used (spare)
38
20A
Not used (spare)
39
20A
Radio
40
20A
Second row heated seats
41
15A
Switch illumination, EC mirror,
Moon roof, Front lock switches,
Radio
42
10A
Not used (spare)
43
10A
Aux relay, Heated back light relay,
rear wiper
44
10A
Not used (spare)
45
5A
Relay coils: PDB, Front and rear
wipers, Front blower motor
46
7.5A
Occupant Classification Sensor
(OCS), Passenger Airbag
Deactivation Indicator (PADI)
47
30A Circuit
Breaker
Power windows
48
Full ISO relay
Delayed accessory relay
Power distribution box
The power distribution box is located in the engine compartment. The
power distribution box contains high-current fuses that protect your
vehicle’s main electrical systems from overloads.
WARNING:
Always disconnect the battery before servicing high
current fuses.
2009 Flex
(471)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
284
WARNING:
To reduce risk of electrical shock, always replace
the cover to the Power Distribution Box before reconnecting the
battery or refilling fluid reservoirs.
If the battery has been disconnected and reconnected, refer to the
Battery
section of the
Maintenance and Specifications
chapter.
The high-current fuses are coded as follows:
Fuse/Relay
Location
Fuse Amp
Rating
Protected Circuits
1
80A*
Passenger compartment fuse
panel power
2
80A*
Passenger compartment fuse
panel power
3
Not used
4
30A*
Front wipers
5
30A*
Passenger power seat
6
20A*
Power point (instrument panel)
7
30A*
Amp
8
Not used
2009 Flex
(471)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
285
Fuse/Relay
Location
Fuse Amp
Rating
Protected Circuits
9
40A*
Anti-lock Brake System
(ABS)/AdvanceTrac pump
10
30A*
Starter
11
30A*
Powertrain Control Module (PCM)
relay
12
20A*
ABS/AdvanceTrac valve
13
20A**
Left HID
14
10A**
Brake on/off (BOO) switch
15
15A**
Refrigerator
16
20A**
Right HID
17
10A**
Alternator
18
20A*
Rear quarter panel power point
19
20A*
Power point (front console)
20
40A*
Rear defroster
21
20A*
Rear console power point
22
20A*
Sub woofer amp
23
7.5A**
PCM Keep alive power, Canister
vent
24
10A**
A/C clutch relay
25
25A**
Rear wiper
26
20A**
Backup relay
27
15A**
Fuel relay (Fuel pump driver
module, Fuel pump)
28
80A*
Cooling fan
29
30A*
E-brake (trailer tow)
30
40A*
Battery charge (trailer tow)
31
30A*
Auxiliary blower relay
32
30A*
Driver seat motors, Memory
module
33
Not used
34
30A*
Power liftgate
35
40A*
Front A/C blower motor
2009 Flex
(471)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
286
Fuse/Relay
Location
Fuse Amp
Rating
Protected Circuits
36
10A**
Back up lamps
37
10A**
PCM run/start
38
5A**
Illumination delayed accessory
39
Diode
Fuel diode
40
Diode
OTIS diode
41
G8VA relay
A/C clutch
42
G8VA relay
Fuel pump
43
G8VA relay
Backup
44
G8VA relay
Refrigerator
45
Not used
46
15A**
VPWR2, VPWR3
47
15A**
PCM VPWR1
48
15A**
PCM VPWR4
49
10A**
Heated mirrors
50
Full ISO relay
PCM relay
51
Full ISO relay
Blower motor relay
52
Full ISO relay
Starter relay
53
Full ISO relay
Rear defrost relay
54
Full ISO relay
Auxiliary blower motor relay
55
Full ISO relay
Front wiper relay
56
Not used
57
Full ISO relay
Rear wiper relay
58
High current
Battery charge relay (trailer tow)
* Cartridge Fuses ** Mini Fuses
2009 Flex
(471)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
287
Auxiliary relay box (if equipped)
The relay box is located in the engine compartment next to the power
distribution box.
Fuse/Relay
location
Fuse amp
rating
Description
1
10A
Trailer tow backup lamp
2
15A
Trailer tow stop/turn lamps
3
Not used
4
Not used
5
Not used
6
Not used
7
Not used
8
Not used
9
Not used
10
Not used
11
Not used
12
20A
Trailer tow park lamps
13
Micro ISO
Trailer tow left turn
14
Micro ISO
Trailer tow right turn
15
Not used
16
Micro ISO
Trailer tow park lamp
2009 Flex
(471)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
288