Ford F-59 Commercial Stripped Chassis - 2015 Fuse Box Diagram

Ford F-59 Commercial Stripped Chassis - 2015 Fuse Box Diagram

1 (First)
Provides maximum engine braking
Allows upshifts by moving gearshift
lever
The transmission will not downshift
into 1 (First) at high speeds; it will
downshift to a lower gear and then
shift into 1 (First) when the vehicle
reaches slower speeds.
Forced downshifts
Allowed in D (Overdrive) with the
tow/haul feature on or off
Press the accelerator to the floor
Allows transmission to select an
appropriate gear
Brake-Shift Interlock
WARNINGS
Do not drive your vehicle until you
verify that the brake lamps are
working.
If your brake lamps are not working
properly or if you have disconnected
the vehicle battery cables, the
vehicle brake lamps and hazard flashers
may not properly warn traffic of a vehicle
breakdown or approaching danger, which
can increase the risk of serious injury or
death. To minimize the risk of serious injury
or death, be aware of your surroundings,
use other hazard signaling devices if
available, and move the vehicle to a safe
location away from traffic as soon as
possible.
When doing this procedure, you will
be taking the vehicle out of park
which means the vehicle can roll
freely. To avoid unwanted vehicle
movement, always fully set the parking
brake prior to doing this procedure. Use
wheel chocks if appropriate.
WARNINGS
If the parking brake is fully released,
but the brake warning lamp remains
illuminated, the brakes may not be
working properly. See your authorized
dealer.
Your vehicle is equipped with a brake-shift
interlock feature that prevents the
gearshift lever from being moved from P
(Park) unless the brake pedal is pressed.
If you cannot move the gearshift lever out
of P (Park) position with the ignition in the
4 (on) position and the brake pedal
pressed, a malfunction may have occurred.
It is possible that a fuse has blown or the
vehicle
s brake lamps are not operating
properly. Refer to Fuses and relays in the
Roadside Emergencies chapter. If the fuses
and brake lamps are working properly, and
the vehicle still will not shift out of (P)
Park, see your authorized dealer for service.
In an emergency, to disable the
malfunctioning brake-shift interlock
feature in order to shift the vehicle from P
(Park) follow these steps:
1.
Apply the parking brake. Turn key to
the lock position, and then remove the
key.
2.
Disconnect the negative (black)
battery cable from the battery.
3.
Insert the key and turn to the off
position. Shift to N (Neutral).
4.
Reconnect the negative (black) battery
cable to the battery.
5.
Start the vehicle.
Note:
See your authorized dealer as soon
as possible if this procedure is used.
31
Motorhome (), enUSA
Transmission
TOWING A TRAILER
WARNINGS
Do not exceed the GVWR or
the GAWR specified on the
certification label.
Towing trailers beyond the
maximum recommended
gross trailer weight exceeds the
limit of the vehicle and could
result in engine damage,
transmission damage, structural
damage, loss of vehicle control,
vehicle rollover and personal
injury.
Your vehicle may have electrical
items, such as fuses or relays,
related to towing. See the
Fuses
chapter.
Your vehicle's load capacity
designation is by weight, not by
volume, so you cannot necessarily
use all available space when
loading a vehicle.
Towing a trailer places an extra
load on your vehicle's engine,
transmission, axle, brakes, tires
and suspension. Inspect these
components periodically during,
and after, any towing operation.
Load Placement
To help minimize how trailer
movement affects your vehicle
when driving:
Load the heaviest items closest
to the trailer floor.
Load the heaviest items
centered between the left and
right side trailer tires.
Load the heaviest items above
the trailer axles or just slightly
forward toward the trailer
tongue. Do not allow the final
trailer tongue weight to go
above or below 10-15% of the
loaded trailer weight.
Select a tow bar with the
correct rise or drop. When both
the loaded vehicle and trailer
are connected, the trailer frame
should be level, or slightly
angled down toward your
vehicle, when viewed from the
side.
When driving with a trailer or
payload, a slight takeoff vibration
or shudder may be present due to
the increased payload weight.
Additional information regarding
proper trailer loading and setting
your vehicle up for towing is
located in another chapter of this
manual. See
Load Limit
(page
36). You can also find the
information in the
RV & Trailer
Towing Guide
, available at an
authorized dealer.
42
Motorhome (), enUSA
Towing
FUSE SPECIFICATION CHART
Power Distribution Box
WARNINGS
Always disconnect the battery before
servicing high current fuses.
To reduce risk of electrical shock,
always replace the cover to the
power distribution box before
reconnecting the battery or refilling fluid
reservoirs.
Locate the power distribution box in the
engine compartment. It has high-current
fuses that protect your vehicle's main
electrical systems from overloads.
If the battery has been disconnected and
reconnected, you will need to reset some
features. See
Changing the 12V Battery
(page 82).
E161519
Protected components
Fuse amp rating
Fuse or relay number
Power brake assist module
Hydromax.
5A*
1
Air conditioning compressor clutch.
10A*
2
Air conditioning clutch relay coil.
20A*
3
Catalyst monitor sensor.
61
Motorhome (), enUSA
Fuses
Protected components
Fuse amp rating
Fuse or relay number
Engine heated exhaust gas oxygen sensor
#11 and #21.
Mass air flow sensor with intake air
temperature.
Vapor management valve.
Powertrain control module memory.
5A*
4
Powertrain control module relay coil.
Powertrain control module power.
20A*
5
Instrument panel dimmer module.
20A*
6
Instrument panel fuse #41.
Park lamp feeds.
Trailer tow running lamp relay coil.
Ignition coils.
20A*
7
Radio capacitors.
Hydromax
Anti-lock brake system
module.
30A*
8
Powertrain control module.
10A*
9
Starter ground relay coil.
Starter main relay coil.
Daytime running lamps.
20A*
10
Fuel pump relay coil.
20A*
11
Powertrain control module power.
Instrument panel - backup lamp feed.
25A*
12
Trailer tow back-up lamps feed.
Trailer tow electric brake controller feed.
30A**
13
Instrument panel battery feed (fuse #9, 15,
21).
60A**
14
Lighting primary fuse.
Trailer tow park lamps.
20A**
15
Anti-lock brake system module
Hydromax.
60A**
16
Anti-lock brake system module
Hydro-
boost.
40A**
Horn feed.
20A**
17
62
Motorhome (), enUSA
Fuses
Protected components
Fuse amp rating
Fuse or relay number
Backup lamp feed.
20A**
18
Tow/haul switch.
Transmission control indicator light.
Not used.
19
Powertrain control module relay coil.
30A**
20
Powertrain control module relay (Power
distribution box fuses # 3, 5, 7, 18).
Fuel injectors.
20A**
21
Fuel pump motor.
Cigar lighter feed.
20A**
22
Diagnostic tool connector.
Blower motor feed.
40A**
23
Instrument panel battery feed (fuses #4,
10, 16, 22).
50A**
24
Ignition switch feed (Instrument panel
fuses #1, 5, 7, 11, 13, 14, 17, 19, 23; Power
distribution box fuses #9, 11).
40A**
25
Ignition switch feed (Instrument panel
fuses #5, 11, 17, 23, 26, 38).
40A**
26
Multi-function switch (headlamps).
30A**
27
Starter solenoid.
30A**
28
Power brake assist motor
Hydromax.
60A**
29
Anti-lock brake system module
Hydro-
boost.
40A**
Air conditioning clutch relay.
R1
Fuel pump relay.
R2
Horn relay.
R3
Starter relay.
R4
Blower motor relay.
R5
Powertrain control module relay.
R6
63
Motorhome (), enUSA
Fuses
Protected components
Fuse amp rating
Fuse or relay number
Fuel pump diode.
Diode 1
Air conditioning clutch diode.
Diode 2
*Mini fuses.
**Maxi fuses.
UPS Power Distribution Box 1
E172543
Protected components
Fuse amp rating
Fuse or relay number
Powertrain control module.
Relay
R1
Daytime running lamps.
Relay
R2
Starter motor.
Relay
R3
Blower motor.
Relay
R4
Horn.
Relay
R5
Fuel pump.
Relay
R6
Starter ground.
Relay
R7
Trailer tow parking lamps.
Relay
R8
Back-up lamps.
Relay
R9
Not used.
Relay
R10
Not used.
Relay
R11
Air conditioning.
Relay
R12
64
Motorhome (), enUSA
Fuses
Protected components
Fuse amp rating
Fuse or relay number
Hydromax brake on/off relay.
10A
M1-1
Not used.
M1-2
Not used.
M1-3
Not used.
M1-4
UPS Power Distribution Box 2
E172544
Protected components
Fuse amp rating
Fuse or relay number
Back-up lamps.
25A*
M1
Daytime running lamps.
20A*
M2
4
channel anti-lock brake system module
(Hydromax).
30A*
M3
Powertrain control module run/start.
20A*
M4
Fuel pump relay coil.
Starter relay coil.
10A*
M5
Vehicle power 4.
20A*
M6
Hydromax motor monitor.
5A*
M7
Vehicle power 2.
20A*
M8
Vehicle power 1.
20A*
M9
Air conditioning.
10A*
M10
65
Motorhome (), enUSA
Fuses
Protected components
Fuse amp rating
Fuse or relay number
Powertrain control module relay keep alive
power.
5A*
M11
Parking lamps.
20A*
M12
One-touch start.
Diode
D1
Fuel pump.
Diode
D2
Air conditioning.
Diode
D3
Not used.
R2-1
Powertrain control module vehicle power.
30A**
J1
Fuel pump.
20A**
J2
Cigar lighter power point.
20A**
J3
Diagnostic connector.
Blower motor.
40A**
J4
Headlamps.
30A**
J5
Ignition switch feeds.
40A**
J6
Ignition switch feeds.
40A**
J7
Instrument panel fuse box.
50A**
J8
Starter motor solenoid.
30A**
J9
3
channel anti-lock brake system module.
40A**
J10
4
channel anti-lock brake system module
(Hydromax).
60A**
Trailer tow electronic brake.
30A**
J11
Lighting.
60A**
J12
Vehicle power 3.
20A**
J13
Horn.
20A**
J14
3
channel anti-lock brake system module.
40A**
J15
66
Motorhome (), enUSA
Fuses
Protected components
Fuse amp rating
Fuse or relay number
4
channel anti-lock brake system module.
60A**
Trailer tow parking lamps.
20A**
J16
*
Mini fuse.
**
J-case fuse.
Diode and Relay Module
Locate the module box with the power
distribution box in from of the radiator.
E161520
Protected components
Relay location
One-touch integrated start (ATO diode).
1
Not used.
2
Not used.
3
Daytime running lamps power relay.
4
Hydromax
brake on/off signal isolating relay.
5
Reverse lamps relay.
6
Starter ground relay.
7
Trailer tow parking lamps relay.
8
67
Motorhome (), enUSA
Fuses
Fuse Holder Module
Locate the fuse holder next to the diode
and relay module.
Protected components
Fuse amp rating
Fuse number
Hydromax
brake on/off signal.
10A
1
Passenger Compartment Fuse
Panel
Locate this fuse panel below and to the
left of the steering wheel near the brake
pedal. Remove the panel cover to access
the fuses.
To remove a fuse, use the fuse panel
cover's fuse puller tool.
E188334
Protected components
Fuse amp rating
Fuse or relay number
Body builder battery (+12V) feed.
20A
1
Flasher run.
20A
2
Left turn.
15A
3
68
Motorhome (), enUSA
Fuses
Protected components
Fuse amp rating
Fuse or relay number
Blower relay coil.
15A
4
Right turn.
15A
5
ABS run.
10A
6
Body builder headlamp.
10A
7
Daytime running lamps.
5A
8
Body builder headlamp.
10A
9
Not used.
10
Cluster battery (+12V) #1.
10A
11
UPS BTSI.
5A
12
Cluster battery (+12V) #2.
10A
13
Switch illumination.
10A
14
Body builder battery (+12V) feed.
20A
15
Not used.
16
Trailer tow run.
20A
17
Body builder run.
10A
18
Brake lamp feed.
10A
19
Body builder run.
10A
20
R/S.
10A
21
Wiper module battery (+12V).
30A
22
Reverse lamps.
10A
23
Body builder radio.
5A
24
Trailer tow reverse lamps.
10A
25
Cluster R/S.
10A
26
Daytime running lamps.
20A
27
Daytime running lamps.
Relay 1
Parking brake.
Daytime running lamps on/off.
Relay 2
69
Motorhome (), enUSA
Fuses
Protected components
Fuse amp rating
Fuse or relay number
Right-hand direction indicator.
Relay 3
Trailer tow right-hand direction indicator.
Relay 4
Left-hand direction indicator.
Relay 5
Trailer tow left-hand direction indicator.
Relay 6
Not used.
Relay 7
Not used.
Relay 8
Not used.
Relay 9
Not used.
Diode 1
Not used.
Diode 2
Not used.
Diode 3
CHANGING A FUSE
Fuses
WARNING
You must replace a failed fuse with
one that has the specified amperage
rating. If you use a fuse with a higher
amperage rating, you may cause severe
wire damage and may start a fire.
E142430
A fuse may fail if electrical components in
the vehicle are not properly working. A
broken wire inside the fuse indicates a
failed fuse. Check the appropriate fuses
before replacing any electrical
components.
70
Motorhome (), enUSA
Fuses