Ford F-450 - 2004 Fuse Box Diagram

Ford F-450 - 2004 Fuse Box Diagram

When closing the moon roof, you should verify that it is free of
obstructions and ensure that children and/or pets are not in the
proximity of the moon roof opening.
AUXILIARY POWER POINT
Power outlets are designed for
accessory plugs only. Do not
hang any type of accessory or
accessory bracket from the plug.
Improper use of the power
outlet can cause damage not
covered by your warranty.
The auxiliary power point is located
on the instrument panel.
Do not plug optional electrical accessories into the cigarette lighter. Use
the power point.
Do not use the power point for operating the cigarette lighter element.
The Maximum power each power point can supply depends on the fuse
rating. For example: a 20A fuse should supply a maximum of 240 Watts,
a 15A fuse should supply a maximum of 180 Watts and a 10A fuse should
supply a maximum of 120 Watts. Exceeding these limits will result in a
blown fuse.
Always keep the power point caps closed when not being used.
POWER WINDOWS (IF EQUIPPED)
When closing the power
windows, you should verify
they are free of obstructions and
ensure that children and/or pets
are not in the proximity of the
window openings.
Press and hold the bottom part of the rocker switch to open the window.
Press and hold the top part of the rocker switch to close the window.
POWER POINT
2004 F250/350/450/550
(f23)
Owners Guide (post-2002-fmt)
USA English
(fus)
Driver Controls
55
The National Highway Traffic Safety Administration (NHTSA)
recommends a minimum distance of at least 25 cm (10 inches)
between an occupant
s chest and the driver air bag module.
Never place your arm over the air bag module as a deploying air
bag can result in serious arm fractures or other injuries.
To properly position yourself away from the air bag:
Move your seat to the rear as far as you can while still reaching the
pedals comfortably.
Recline the seat slightly one or two degrees from the upright position.
Do not put anything on or over the air bag module. Placing
objects on or over the air bag inflation area may cause those
objects to be propelled by the air bag into your face and torso causing
serious injury.
Do not attempt to service, repair, or modify the air bag
supplemental restraint systems or its fuses. See your Ford or
Lincoln Mercury dealer.
The front passenger air bag is not designed to offer protection to
an occupant in the center front seating position.
Modifying or adding equipment to the front end of the vehicle
(including frame, bumper, front end body structure and tow
hooks) may affect the performance of the air bag system, increasing
the risk of injury. Do not modify the front end of the vehicle.
Additional equipment such as snowplow equipment may effect
the performance of the air bag sensors increasing the risk of
injury. Please refer to the Body Builders Layout Book for instructions
about the appropriate installation of additional equipment.
Removing the blocker beam without installing snow plow
attachment hardware may effect air bag deployment in a crash.
Do not operate the truck unless either the blocker beam or snow plow
attachment hardware is installed on the vehicle.
2004 F250/350/450/550
(f23)
Owners Guide (post-2002-fmt)
USA English
(fus)
Seating and Safety Restraints
105
Loaded vehicles, with a higher center of gravity, may handle
differently than unloaded vehicles. Extra precautions, such as
slower speeds and increased stopping distance, should be taken when
driving a heavily loaded vehicle.
AUTOMATIC TRANSMISSION OPERATION (IF EQUIPPED)
Brake-shift interlock
This vehicle is equipped with a brake-shift interlock feature that prevents
the gearshift lever from being moved from P (Park) when the ignition is
in the ON position unless brake pedal is depressed.
If you cannot move the gearshift lever out of P (Park) with ignition in
the ON position and the brake pedal depressed:
1. Apply the parking brake, turn ignition key to LOCK, then remove the
key.
2. Insert the key and turn it to OFF.
Apply the brake pedal and shift
to N (Neutral)
.
When the key is in the ignition and in the OFF position, the
automatic transmission shift lever can be moved from the P
(Park) position without the brake pedal depressed. To avoid unwanted
vehicle movement, always set the parking brake.
3. Start the vehicle.
If it is necessary to use the above procedure to move the gearshift lever,
it is possible that a fuse has blown or the vehicle
s brakelamps are not
operating properly. Refer to
Fuses and relays
in the
Roadside
emergencies
chapter.
Do not drive your vehicle until you verify that the brakelamps
are working.
Always set the parking brake fully and make sure the gearshift is
latched in P (Park). Turn the ignition to the LOCK position and
remove the key whenever you leave your vehicle.
2004 F250/350/450/550
(f23)
Owners Guide (post-2002-fmt)
USA English
(fus)
Driving
132
Your vehicle may be equipped with a temporary or conventional spare
tire. If the spare tire is different in size (diameter and/or width), tread
type (All-Season or All-Terrain) or is from a different manufacturer
other than the road tires on your vehicle, your spare tire is considered
temporary
. Consult information on the spare tire label for limitations
when using.
Servicing after towing
If you tow a trailer for long distances, your vehicle will require more
frequent service intervals. Refer to your scheduled maintenance guide for
more information.
Trailer towing tips
Practice turning, stopping and backing up before starting on a trip to
get the feel of the vehicle trailer combination. When turning, make
wider turns so the trailer wheels will clear curbs and other obstacles.
Allow more distance for stopping with a trailer attached.
The trailer tongue weight should be 10
15% of the loaded trailer
weight.
After you have traveled 80 km (50 miles), thoroughly check your
hitch, electrical connections and trailer wheel lug nuts.
To aid in engine/transmission cooling and A/C efficiency during hot
weather while stopped in traffic, place the gearshift lever in P (Park)
(automatic transmission) or N (Neutral) (manual transmissions).
Vehicles with trailers should not be parked on a grade. If you must
park on a grade, place wheel chocks under the trailer
s wheels.
Launching or retrieving a boat
When backing down a ramp during boat launching or retrieval,
Do not allow the static water level to rise above the bottom edge of
the rear bumper.
Do not allow waves to break higher than 15 cm (6 inches) above the
bottom edge of the rear bumper.
Disconnect the trailer tow electrical connector to prevent blown fuses
caused by water entering into your trailer
s electrical wiring.
Exceeding these limits may allow water to enter critical vehicle
components, adversely affecting driveability, emissions and reliability.
Replace front and rear axle lubricants any time the axles have been
submerged in water. Axle lubricant quantities are not to be checked
unless a leak is suspected.
2004 F250/350/450/550
(f23)
Owners Guide (post-2002-fmt)
USA English
(fus)
Driving
186
Snowplowing with your air bag-equipped vehicle
Your vehicle is equipped with a driver and passenger air bag
Supplemental Restraint System (SRS) The SRS is designed to activate in
certain frontal and offset frontal collisions when the vehicle sustains
sufficient longitudinal deceleration.
Careless or high speed driving while plowing snow which results in
sufficient vehicle decelerations can deploy the air bag. Such driving also
increases the risk of accidents.
All occupants of the vehicle, including the driver, should always
properly wear their safety belts, even when an air bag (SRS) is
provided.
Never remove or defeat the
tripping mechanisms
designed into the
snow removal equipment by its manufacturer. Doing so may cause
damage to the vehicle and the snow removal equipment as well as
possible air bag deployment.
Do not attempt to service, repair, or modify the Air Bag
Supplemental Restraint System or its fuses. See your Ford or
Lincoln Mercury dealer.
Additional equipment such as snowplow equipment may effect
the performance of the air bag sensors increasing the risk of
injury. Please refer to the Body Builders Layout Book for instructions
about the appropriate installation of additional equipment.
Transmission operation while plowing
Shift transfer case to 4x4 LOW (4WD Low) when plowing in small
areas at speeds below 8 km/h (5 mph).
Shift transfer case to 4x4 HIGH (4WD High) when plowing larger
areas or light snow at higher speeds. Do not exceed 24 km/h (15
mph).
Do not shift the transmission from a forward gear to R (Reverse) until
the engine is at idle and the wheels are stopped.
2004 F250/350/450/550
(f23)
Owners Guide (post-2002-fmt)
USA English
(fus)
Driving
189
This switch is located in the front
passenger
s footwell, by the kick
panel access cover.
To reset the switch:
1. Turn the ignition OFF.
2. Check the fuel system for leaks.
3. If no leaks are apparent, reset the
switch by pushing in on the reset
button.
4. Turn the ignition ON.
5. Wait a few seconds and return
the key to OFF.
6. Make another check of leaks.
FUSES AND RELAYS
Fuses
If electrical components in the
vehicle are not working, a fuse may
have blown. Blown fuses are
identified by a broken wire within
the fuse. Check the appropriate
fuses before replacing any electrical
components.
Note:
Always replace a fuse with one that has the specified amperage
rating. Using a fuse with a higher amperage rating can cause severe wire
damage and could start a fire.
15
2004 F250/350/450/550
(f23)
Owners Guide (post-2002-fmt)
USA English
(fus)
Roadside Emergencies
193
Standard fuse amperage rating and color
COLOR
Fuse
rating
Mini
fuses
Standard
fuses
Maxi
fuses
Cartridge
maxi
fuses
Fuse link
cartridge
2A
Grey
Grey
3A
Violet
Violet
4A
Pink
Pink
5A
Tan
Tan
7.5A
Brown
Brown
10A
Red
Red
15A
Blue
Blue
20A
Yellow
Yellow
Yellow
Blue
Blue
25A
Natural
Natural
30A
Green
Green
Green
Pink
Pink
40A
Orange
Green
Green
50A
Red
Red
Red
60A
Blue
Yellow
70A
Tan
Brown
80A
Natural
Black
Passenger compartment fuse panel / power distribution box
The fuse panel is located below and to the left of the steering wheel by
the brake pedal. Remove the panel cover to access the fuses.
To remove the fuse panel cover,
turn the panel fasteners
counterclockwise.
2004 F250/350/450/550
(f23)
Owners Guide (post-2002-fmt)
USA English
(fus)
Roadside Emergencies
194
To remove a fuse use the fuse puller
tool provided on the fuse panel
cover.
The fuses are coded as follows.
Fuse/Relay
Location
Fuse Amp
Rating
Passenger Compartment Fuse
Panel Description
1
15A*
Adjustable pedals
2
Not used
3
Not used
4
20A*
Power point - instrument panel
5
Not used
6
20A*
Trailer tow turn/stop relay
7
30A*
High beam headlamps/Flash to
pass
8
15A*
Backup lamps (Diesel engine
only)
9
20A*
Heated mirrors
2004 F250/350/450/550
(f23)
Owners Guide (post-2002-fmt)
USA English
(fus)
Roadside Emergencies
195
Fuse/Relay
Location
Fuse Amp
Rating
Passenger Compartment Fuse
Panel Description
10
10A*
A/C clutch
11
20A*
Radio (main)
12
20A*
Cigar lighter / OBD II
13
5A*
Power mirrors/switches
14
15A*
Daytime running lamps (DRL)
15
Not used
16
Not used
17
15A*
Exterior lamps
18
20A*
Turn lamps/Brake on-off switch
(high)
19
10A*
Body security module/4x4 module
20
10A*
Fuel Injection Control Module
(FICM) relay (Diesel engine only)
21
Not used
22
20A*
Engine control
23
20A*
Engine control (gasoline engine
only), Climate control (Diesel
engine only)
24
2A*
Brake pressure switch/Speed
control
25
10A*
4-Wheel Anti-lock Brake System
(4WABS) module, Variable Fan
Control (VFC) (Diesel engine
only)
26
10A*
Air bags
27
15A*
Ignition switch Run feed
28
10A*
EATC module/Front blower relay
coil
29
10A*
Customer access
30
15A*
Highbeam headlamps
2004 F250/350/450/550
(f23)
Owners Guide (post-2002-fmt)
USA English
(fus)
Roadside Emergencies
196
Fuse/Relay
Location
Fuse Amp
Rating
Passenger Compartment Fuse
Panel Description
31
15A*
Clutch interlock switch (manual
transmissions only), Transmission
range sensor (automatic
transmissions only) then to
starter relay coil (all
transmissions), 4x4
32
5A*
Radio (start)
33
15A*
Front wiper
34
10A*
Brake on-off switch
35
10A*
Instrument cluster
36
10A*
PCM Memory
37
15A*
Horn
38
20A*
Trailer tow park lamps
39
15A*
Trailer tow back-up lamps
40
20A*
Fuel pump
41
10A*
Instrument cluster
42
15A*
Delayed accessory
43
10A*
Fog lamps
44
Not used
45
10A*
Ignition switch Run/Start feed
46
10A*
Left-hand lowbeam
47
10A*
Right-hand lowbeam
48
Not used
101
30A**
Trailer tow electric brake
102
30A**
Door locks/Body security module
103
50A**
Ignition switch (gasoline engine
only), FICM power (Diesel engine
only)
104
40A**
Heated backlight
105
30A**
Fuel heater (Diesel engine only)
106
30A**
Front wiper main
107
40A**
Front blower motor
2004 F250/350/450/550
(f23)
Owners Guide (post-2002-fmt)
USA English
(fus)
Roadside Emergencies
197
Fuse/Relay
Location
Fuse Amp
Rating
Passenger Compartment Fuse
Panel Description
108
Not used
109
30A**
Heated seats
110
50A**
Ignition switch
111
30A**
4WD/Shift on the fly
112
30A**
Left-hand power seats
113
30A**
Starter motor
114
30A**
Right-hand power seats
115
20A**
Trailer tow battery charge
116
30A**
Ignition switch
601
30A CB***
Window motors, Moonroof
602
60A**
4WABS module
210
Not used
211
Backup lamps relay (Diesel engine
only)
212
Not used
301
Front blower motor relay
302
Powertrain Control Module (PCM)
relay
303
Fuel heater relay (Diesel engine
only)
304
Heated backlight relay
305
Trailer tow battery charge relay
306
Delayed accessory relay
307
Starter relay
* Mini Fuses ** Maxi Fuses ***Circuit Breaker
Note: (Diesel engine only)
The Fuel Injection Control Module (FICM)
logic 15A mini-fuse is located in the underhood relay block.
CHANGING A FLAT TIRE
If you get a flat tire while driving:
do not brake heavily.
gradually decrease the vehicle
s speed.
hold the steering wheel firmly.
2004 F250/350/450/550
(f23)
Owners Guide (post-2002-fmt)
USA English
(fus)
Roadside Emergencies
198