Ford Explorer Sport Trac - 2007 Fuse Box Diagram

Ford Explorer Sport Trac - 2007 Fuse Box Diagram

AUXILIARY POWER POINT (12VDC)
Power outlets are designed for accessory plugs only. Do not insert
any other object in the power outlet as this will damage the
outlet and blow the fuse. Do not hang any type of accessory or
accessory bracket from the plug. Improper use of the power
outlet can cause damage not covered by your warranty.
The auxiliary power point is located
in the floor console.
Do not use the power point for
operating the cigarette lighter
element (if equipped).
To prevent the fuse from being
blown, do not use the power
point(s) over the vehicle capacity of
12 VDC/180W.
To prevent the battery from being
discharged, do not use the power point longer than necessary when the
engine is not running.
Always keep the power point caps closed when not being used.
Cigar/Cigarette lighter (if equipped)
Do not plug optional electrical accessories into the cigarette lighter
socket.
Do not hold the lighter in with your hand while it is heating, this will
damage the lighter element and socket. The lighter will be released from
its heating position when it is ready to be used.
Improper use of the lighter can cause damage not covered by your
warranty.
Rear auxiliary power point
A second auxiliary power point is located on the rear side of the console.
It is accessible from the rear seats.
2007 07+ Explorer Sport Trac
(esp)
Owners Guide (post-2002-fmt)
USA
(fus)
Driver Controls
54
Do not attempt to service, repair, or modify the airbag
supplemental restraint systems or its fuses. See your authorized
dealer.
Modifications to the front end of the vehicle, including frame,
bumper, front end body structure and non-Ford tow hooks may
effect the performance of the airbag sensors increasing the risk of
injury. Do not modify the front end of the vehicle with anything other
than authorized Ford accessories for your vehicle.
Additional equipment may affect the performance of the airbag
sensors increasing the risk of injury. Please refer to the
Body
Builders Layout Book
for instructions about the appropriate
installation of additional equipment.
Children and airbags
Children must always be properly
restrained. Accident statistics
suggest that children are safer when
properly restrained in the rear
seating positions than in the front
seating position. Failure to follow
these instructions may increase the
risk of injury in a collision.
Airbags can kill or injure a
child in a child seat.
NEVER
place a rear-facing child
seat in front of an active airbag. If
you must use a forward-facing
child seat in the front seat, move
the seat all the way back.
2007 07+ Explorer Sport Trac
(esp)
Owners Guide (post-2002-fmt)
USA
(fus)
Seating and Safety Restraints
133
Do not attempt to service, repair, or modify the airbag SRS, its
fuses or the seat cover on a seat containing an airbag. See your
authorized dealer.
All occupants of the vehicle should always wear their safety belts
even when an airbag SRS is provided.
How does the side airbag system work?
The design and development of the side airbag system included
recommended testing procedures that were developed by a group of
automotive safety experts known as the Side Airbag Technical Working
Group. These recommended testing procedures help reduce the risk of
injuries related to the deployment of side airbags.
The side airbag system consists of
the following:
An inflatable nylon bag (airbag)
with an inflator concealed behind
the outboard bolster of the driver
and front passenger seatbacks.
A special seat cover designed to
allow airbag deployment.
The same warning light,
electronic control and diagnostic
unit as used for the front airbags.
Crash sensors located on the
front doors and C pillars (one
sensor on each pillar on each side
of the vehicle).
Side airbags, in combination with
safety belts, can help reduce the risk of severe injuries in the event of a
significant side impact collision.
The side airbags are fitted on the outboard side of the seatbacks of the
front seats. In certain lateral collisions, the airbag on the side affected by
the collision will be inflated. If the front passenger sensing system
detects an empty seat, the front passenger seat-mounted side airbag will
be deactivated. The airbag was designed to inflate between the door
panel and occupant to further enhance the protection provided
occupants in side impact collisions.
2007 07+ Explorer Sport Trac
(esp)
Owners Guide (post-2002-fmt)
USA
(fus)
Seating and Safety Restraints
141
Do not lean your head on the door. The Safety Canopy
³
could
injure you as it deploys from the headliner.
Do not attempt to service, repair, or modify the Safety Canopy
³
system, its fuses, the A, B, or C pillar trim, or the headliner on a
vehicle containing a Safety Canopy
³
. See your authorized dealer.
All occupants of the vehicle including the driver should always
wear their safety belts even when an airbag SRS and Safety
Canopy
³
system is provided.
To reduce risk of injury, do not obstruct or place objects in the
deployment path of the inflatable Safety Canopy
³
.
How does the Safety Canopy
´
system work?
The design and development of the
Safety Canopy
³
system included
recommended testing procedures
that were developed by a group of
automotive safety experts known as
the Side Airbag Technical Working
Group. These recommended testing
procedures help reduce the risk of
injuries related to the deployment of
side airbags (including the Safety
Canopy
³
).
The Safety Canopy
³
system
consists of the following:
An inflatable nylon curtain with
an inflator concealed behind the
headliner and above the doors
(one on each side of the vehicle).
2007 07+ Explorer Sport Trac
(esp)
Owners Guide (post-2002-fmt)
USA
(fus)
Seating and Safety Restraints
143
4. Apply the brake and shift into N (Neutral).
5. Return the cover plug to the console access hole. Start the vehicle.
If it is necessary to use the above procedure to move the gearshift lever,
it is possible that a fuse has blown or the vehicle’s brakelamps are not
operating properly. Refer to
Fuses and relays
in the
Roadside
Emergencies
chapter.
Do not drive your vehicle until you verify that the brakelamps
are working.
Always set the parking brake fully and make sure the gearshift is
latched in P (Park). Turn the ignition to the LOCK position and
remove the key whenever you leave your vehicle.
If the parking brake is fully released, but the brake warning lamp
remains illuminated, the brakes may not be working properly.
See your authorized dealer.
2007 07+ Explorer Sport Trac
(esp)
Owners Guide (post-2002-fmt)
USA
(fus)
Driving
204
The fuel pump shut-off switch is
located in the passenger’s foot well,
by the kick panel.
Use the following procedure to reset the fuel pump shut-off switch.
1. Turn the ignition to the OFF position.
2. Check the fuel system for leaks.
3. If no fuel leak is apparent, reset the fuel pump shut-off switch by
pushing in on the reset button.
4. Turn the ignition to the ON position. Pause for a few seconds and
return the key to the OFF position.
5. Make a further check for leaks in the fuel system.
FUSES AND RELAYS
Fuses
If electrical components in the
vehicle are not working, a fuse may
have blown. Blown fuses are
identified by a broken wire within
the fuse. Check the appropriate
fuses before replacing any electrical
components.
15
2007 07+ Explorer Sport Trac
(esp)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
224
Note:
Always replace a fuse with one that has the specified amperage
rating. Using a fuse with a higher amperage rating can cause severe wire
damage and could start a fire.
Standard fuse amperage rating and color
COLOR
Fuse
rating
Mini fuses
Standard
fuses
Maxi fuses
Cartridge
maxi fuses
2A
Grey
Grey
3A
Violet
Violet
4A
Pink
Pink
5A
Tan
Tan
7.5A
Brown
Brown
10A
Red
Red
15A
Blue
Blue
20A
Yellow
Yellow
Yellow
Blue
25A
Natural
Natural
30A
Green
Green
Green
Pink
40A
Orange
Green
50A
Red
Red
60A
Blue
Yellow
70A
Tan
80A
Natural
2007 07+ Explorer Sport Trac
(esp)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
225
Passenger compartment fuse panel
The fuse panel is located below the
instrument panel on the driver’s
side.
To remove a fuse use the fuse puller tool provided on the fuse panel box.
The fuses are coded as follows:
Fuse/Relay
Location
Fuse Amp
Rating
Passenger Compartment Fuse
Panel Description
1
20A
Moonroof, Adjustable pedals
2
5A
Microcontroller power (SJB)
3
20A
Radio
4
20A
OBD II connector
5
5A
Moonroof, Power down back window
6
20A
Door unlock/lock
7
15A
Trailer tow stop/turn lamps
CB1
4
3
2
1
8
7
6
5
12
11
10
9
16
15
14
13
20
19
18
17
24
23
22
21
28
27
26
25
2007 07+ Explorer Sport Trac
(esp)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
226
Fuse/Relay
Location
Fuse Amp
Rating
Passenger Compartment Fuse
Panel Description
8
15A
Ignition switch power, PATS
9
2A
6-speed transmission/PCM (Ignition
RUN/START), Fuel pump relay
10
5A
Front wiper RUN/ACC (relay in PDB)
11
5A
Radio start
12
5A
RUN accessory – Radio, Trailer tow
battery charge (relay in PDB)
13
15A
Spare
14
20A
Horn
15
10A
Reverse lamps
16
10A
Trailer tow reverse lamps
17
10A
RUN/START – RCM (restraints), PAD
lamp, OCS module
18
10A
RUN/START – IVD switch, IVD, 4x4
module, 4x4 switch, Heated seat
switches, Compass, Electrochromatic
mirror
19
Not used
20
10A
RUN/START – Manual climate control,
DEATC, Brake shift
21
Not used
22
15A
Brake switch, Stop lamps, Turn lamps
23
15A
Power mirrors, Interior lamps, Puddle
lamps, Cargo lamp, Battery saver,
Instrument illumination
24
10A
Instrument cluster, Theft LED
25
15A
Trailer tow park lamps, Trailer tow
electronic brake module
26
15A
License plate lamps, Rear park lamps,
Front park lamps, Manual climate
control
27
15A
Tricolor tail lamps (stop lamps )
2007 07+ Explorer Sport Trac
(esp)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
227
Fuse/Relay
Location
Fuse Amp
Rating
Passenger Compartment Fuse
Panel Description
28
10A
Manual/DEATC climate control
CB1
25A
Windows
The following relays are located on either side of the passenger
compartment fuse panel. See your authorized dealer for service of these
relays.
Fuse/Relay Location
Description
Relay 1
Delayed ACC
Relay 2
Not used
Relay 3
Park lamps
Relay 4
RUN/START
Power distribution box
The power distribution box is
located in the engine compartment.
The power distribution box contains
high-current fuses that protect your
vehicle’s main electrical systems
from overloads.
Always disconnect the battery before servicing high current
fuses.
To reduce risk of electrical shock, always replace the cover to
the Power Distribution Box before reconnecting the battery or
refilling fluid reservoirs.
If the battery has been disconnected and reconnected, refer to the
Battery
section of the
Maintenance and Specifications
chapter.
2007 07+ Explorer Sport Trac
(esp)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
228
The high-current fuses are coded as follows:
Fuse/Relay
Location
Fuse Amp
Rating
Power Distribution Box
Description
1
50A**
BATT 2 (SJB)
2
50A**
BATT 3 (SJB)
3
50A**
BATT 1 (SJB)
4
30A**
Fuel pump, Fuel injectors
5
Not used
6
40A**
IVD module – pump
7
40A**
Powertrain Control Module
(PCM)
8
40A**
Heated windshield (left)
9
40A**
Heated windshield (right)
10
30A**
Power down back window
11
30A**
Starter
12
Not used
13
30A**
Trailer tow battery charge
14
40A**
Power drivers seat
21
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
25
29
33
37
41
22
51
55
56
54
49
48
47
46B
46A
45B
45A
50B
50A
52
53
26
30
34
38
42
23
27
31
35
39
43
24
28
32
36
40
44
2007 07+ Explorer Sport Trac
(esp)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
229
Fuse/Relay
Location
Fuse Amp
Rating
Power Distribution Box
Description
15
40A**
Not used
16
40A**
Blower motor
17
30A**
Trailer tow electronic brakes
18
Not used
19
Not used
20
Not used
21
20A*
Rear of console power point
22
20A*
Subwoofer, Satellite radio
23
20A*
4x4 module
24
10A*
Powertrain Control Module
(PCM) KAP, CAN vent
25
20A*
Front of console power
point/Cigar lighter
26
20A*
4x4 module
27
20A*
6–speed transmission control
module (TCM)
28
20A*
Heated seats
29
20A*
Right high/low beam headlamp
30
20A*
Cargo bed power point
31
15A*
Fog lamps
32
Not used
33
30A*
IVD module – valves
34
20A*
Left high/low beam headlamp
35
10A*
AC clutch
36
Not used
37
30A*
Front wiper
38
15A*
5–speed transmission
39
15A*
PCM power
40
15A*
Fan clutch, PCV valve (4.0L
engine only), AC clutch relay
41
Not used
2007 07+ Explorer Sport Trac
(esp)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
230
Fuse/Relay
Location
Fuse Amp
Rating
Power Distribution Box
Description
42
15A*
Speed control deactivation
switch, EVMV, MAFS, HEGO,
EVR, CMS, (VCT1, VCT2, CMCV
on 4.6L only)
43
15A*
Coil on plug (4.6L engine), Coil
tower (4.0L engine)
44
15A*
Fuel injectors
45A
Not used
45B
Not used
46A
Not used
46B
Not used
47
Front wiper relay
48
PCM relay
49
Fuel pump relay
50A
Fog lamps relay
50B
AC clutch relay
51
Not used
52
A/C clutch diode
53
Not used
54
Trailer tow battery charge relay
55
Starter relay
56
Climate control blower relay
* Mini Fuses ** Cartridge Fuses
CHANGING THE TIRES
If you get a flat tire while driving:
do not brake heavily.
gradually decrease the vehicle’s speed.
hold the steering wheel firmly.
slowly move to a safe place on the side of the road.
Note:
The tire pressure monitoring system (TPMS) indicator light will
illuminate when the spare is in use. To restore the full functionality of
the monitoring system, all road wheels equipped with tire pressure
monitoring sensors must be mounted on the vehicle.
2007 07+ Explorer Sport Trac
(esp)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
231
Installing a garage door opener (if equipped)
The storage compartment can be converted to accommodate a variety of
aftermarket garage door openers:
Place the VELCRO
±
hook onto
the side of the aftermarket
transmitter opposite of the
button.
Place the transmitter into storage
compartment, button down.
Place the provided height
adaptors onto the back of the
door as needed.
Close the door.
Press the depression in the door
to activate the transmitter.
AUXILIARY POWER POINT (12VDC)
Power outlets are designed for accessory plugs only. Do not insert
any other object in the power outlet as this will damage the
outlet and blow the fuse. Do not hang any type of accessory or
accessory bracket from the plug. Improper use of the power
outlet can cause damage not covered by your warranty.
2007 07+ Explorer Sport Trac
(esp)
Owners Guide (post-2002-fmt)
USA
(fus)
Driver Controls
61
The auxiliary power point is located
in the floor console.
Do not use the power point for
operating the cigarette lighter
element (if equipped).
To prevent the fuse from being
blown, do not use the power
point(s) over the vehicle capacity of
12 VDC/180W.
To prevent the battery from being
discharged, do not use the power point longer than necessary when the
engine is not running.
Always keep the power point caps closed when not being used.
Cigar/Cigarette lighter (if equipped)
Do not plug optional electrical accessories into the cigarette lighter
socket.
Do not hold the lighter in with your hand while it is heating, this will
damage the lighter element and socket. The lighter will be released from
its heating position when it is ready to be used.
Improper use of the lighter can cause damage not covered by your
warranty.
Rear auxiliary power point
A second auxiliary power point is located on the rear side of the console.
It is accessible from the rear seats.
Truck bed auxiliary power point
An additional auxiliary power point
is located in the bed of the truck
(12V 20AMP max).
Lift the cover to access the auxiliary
power point.
2007 07+ Explorer Sport Trac
(esp)
Owners Guide (post-2002-fmt)
USA
(fus)
Driver Controls
62
Do not attempt to service, repair, or modify the airbag
supplemental restraint systems or its fuses. See your authorized
dealer.
Modifications to the front end of the vehicle, including frame,
bumper, front end body structure and non-Ford tow hooks may
effect the performance of the airbag sensors increasing the risk of
injury. Do not modify the front end of the vehicle with anything other
than authorized Ford accessories for your vehicle.
Additional equipment may affect the performance of the airbag
sensors increasing the risk of injury. Please refer to the
Body
Builders Layout Book
for instructions about the appropriate
installation of additional equipment.
Children and airbags
Children must always be properly
restrained. Accident statistics
suggest that children are safer when
properly restrained in the rear
seating positions than in the front
seating position. Failure to follow
these instructions may increase the
risk of injury in a collision.
Airbags can kill or injure a
child in a child seat.
NEVER
place a rear-facing child
seat in front of an active airbag. If
you must use a forward-facing
child seat in the front seat, move
the seat all the way back.
2007 07+ Explorer Sport Trac
(esp)
Owners Guide (post-2002-fmt)
USA
(fus)
Seating and Safety Restraints
144
Do not attempt to service, repair, or modify the airbag SRS, its
fuses or the seat cover on a seat containing an airbag. See your
authorized dealer.
All occupants of the vehicle should always wear their safety belts
even when an airbag SRS is provided.
How does the side airbag system work?
The design and development of the side airbag system included
recommended testing procedures that were developed by a group of
automotive safety experts known as the Side Airbag Technical Working
Group. These recommended testing procedures help reduce the risk of
injuries related to the deployment of side airbags.
The side airbag system consists of
the following:
An inflatable nylon bag (airbag)
with an inflator concealed behind
the outboard bolster of the driver
and front passenger seatbacks.
A special seat cover designed to
allow airbag deployment.
The same warning light,
electronic control and diagnostic
unit as used for the front airbags.
Crash sensors located on the
front doors and C pillars (one
sensor on each pillar on each side
of the vehicle).
Side airbags, in combination with
safety belts, can help reduce the risk of severe injuries in the event of a
significant side impact collision.
The side airbags are fitted on the outboard side of the seatbacks of the
front seats. In certain lateral collisions, the airbag on the side affected by
the collision will be inflated. If the front passenger sensing system
detects an empty seat, the front passenger seat-mounted side airbag will
be deactivated. The airbag was designed to inflate between the door
panel and occupant to further enhance the protection provided
occupants in side impact collisions.
2007 07+ Explorer Sport Trac
(esp)
Owners Guide (post-2002-fmt)
USA
(fus)
Seating and Safety Restraints
152
Do not lean your head on the door. The Safety Canopy
³
could
injure you as it deploys from the headliner.
Do not attempt to service, repair, or modify the Safety Canopy
³
system, its fuses, the A, B, or C pillar trim, or the headliner on a
vehicle containing a Safety Canopy
³
. See your authorized dealer.
All occupants of the vehicle including the driver should always
wear their safety belts even when an airbag SRS and Safety
Canopy
³
system is provided.
To reduce risk of injury, do not obstruct or place objects in the
deployment path of the inflatable Safety Canopy
³
.
How does the Safety Canopy
´
system work?
The design and development of the
Safety Canopy
³
system included
recommended testing procedures
that were developed by a group of
automotive safety experts known as
the Side Airbag Technical Working
Group. These recommended testing
procedures help reduce the risk of
injuries related to the deployment of
side airbags (including the Safety
Canopy
³
).
The Safety Canopy
³
system
consists of the following:
An inflatable nylon curtain with
an inflator concealed behind the
headliner and above the doors
(one on each side of the vehicle).
2007 07+ Explorer Sport Trac
(esp)
Owners Guide (post-2002-fmt)
USA
(fus)
Seating and Safety Restraints
154
2. Remove the rubber pad at the
bottom of the cup holder to locate
the access cap of the floor shifter
assembly.
3. Using a screwdriver (or
equivalent), remove the access
panel and depress the shifter lever
on the shift mechanism.
4. Apply the brake and shift into N (Neutral).
5. Return the cover plug to the console access hole. Start the vehicle.
If it is necessary to use the above procedure to move the gearshift lever,
it is possible that a fuse has blown or the vehicle’s brakelamps are not
operating properly. Refer to
Fuses and relays
in the
Roadside
Emergencies
chapter.
Do not drive your vehicle until you verify that the brakelamps
are working.
Always set the parking brake fully and make sure the gearshift is
latched in P (Park). Turn the ignition to the LOCK position and
remove the key whenever you leave your vehicle.
If the parking brake is fully released, but the brake warning lamp
remains illuminated, the brakes may not be working properly.
See your authorized dealer.
2007 07+ Explorer Sport Trac
(esp)
Owners Guide (post-2002-fmt)
USA
(fus)
Driving
218
The fuel pump shut-off switch is
located in the passenger’s foot well,
by the kick panel.
Use the following procedure to reset the fuel pump shut-off switch.
1. Turn the ignition to the OFF position.
2. Check the fuel system for leaks.
3. If no fuel leak is apparent, reset the fuel pump shut-off switch by
pushing in on the reset button.
4. Turn the ignition to the ON position. Pause for a few seconds and
return the key to the OFF position.
5. Make a further check for leaks in the fuel system.
FUSES AND RELAYS
Fuses
If electrical components in the
vehicle are not working, a fuse may
have blown. Blown fuses are
identified by a broken wire within
the fuse. Check the appropriate
fuses before replacing any electrical
components.
15
2007 07+ Explorer Sport Trac
(esp)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
239
Note:
Always replace a fuse with one that has the specified amperage
rating. Using a fuse with a higher amperage rating can cause severe wire
damage and could start a fire.
Standard fuse amperage rating and color
COLOR
Fuse
rating
Mini fuses
Standard
fuses
Maxi fuses
Cartridge
maxi fuses
2A
Grey
Grey
3A
Violet
Violet
4A
Pink
Pink
5A
Tan
Tan
7.5A
Brown
Brown
10A
Red
Red
15A
Blue
Blue
20A
Yellow
Yellow
Yellow
Blue
25A
Natural
Natural
30A
Green
Green
Green
Pink
40A
Orange
Green
50A
Red
Red
60A
Blue
Yellow
70A
Tan
80A
Natural
2007 07+ Explorer Sport Trac
(esp)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
240
Passenger compartment fuse panel
The fuse panel is located below the
instrument panel on the driver’s
side.
To remove a fuse use the fuse puller tool provided on the fuse panel box.
The fuses are coded as follows:
Fuse/Relay
Location
Fuse Amp
Rating
Passenger Compartment Fuse
Panel Description
1
20A
Moon roof, Adjustable pedals
2
5A
Microcontroller power (SJB)
3
20A
Radio
4
20A
OBD II connector
5
5A
Moonroof, Power down back
window
6
20A
Door unlock/lock
CB1
4
3
2
1
8
7
6
5
12
11
10
9
16
15
14
13
20
19
18
17
24
23
22
21
28
27
26
25
2007 07+ Explorer Sport Trac
(esp)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
241
Fuse/Relay
Location
Fuse Amp
Rating
Passenger Compartment Fuse
Panel Description
7
15A
Trailer tow stop/turn lamps
8
15A
Ignition switch power, PATS
9
2A
6-speed transmission/PCM
(Ignition RUN/START), Fuel
pump relay
10
5A
Front wiper RUN/ACC (relay in
PDB)
11
5A
Radio start
12
5A
RUN accessory – Radio, Trailer
tow battery charge (relay in PDB)
13
15A
Spare
14
20A
Horn
15
10A
Reverse lamps
16
10A
Trailer tow reverse lamps
17
10A
RUN/START – RCM (restraints),
PAD lamp, OCS module
18
10A
RUN/START – IVD switch, IVD,
4x4 module, 4x4 switch, Heated
seat switches, Compass,
Electrochromatic mirror, RSS
module
19
Not used
20
10A
RUN/START – Manual climate
control, DEATC, Brake shift
21
Not used
22
15A
Brake switch, Stop lamps, Turn
lamps
23
15A
Interior lamps, Puddle lamps,
Cargo lamp, Battery saver,
Instrument illumination
24
10A
Instrument cluster, Theft LED
2007 07+ Explorer Sport Trac
(esp)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
242
Fuse/Relay
Location
Fuse Amp
Rating
Passenger Compartment Fuse
Panel Description
25
15A
Trailer tow park lamps, Trailer
tow electronic brake module
26
15A
License plate lamps, Rear park
lamps, Front park lamps, Manual
climate control
27
15A
Not used
28
10A
Manual/DEATC climate control
CB1
25A
Windows
The following relays are located on either side of the passenger
compartment fuse panel. See your authorized dealer for service of these
relays.
Fuse/Relay Location
Description
Relay 1
Delayed ACC
Relay 2
Not used
Relay 3
Park lamps
Relay 4
RUN/START
Power distribution box
The power distribution box is
located in the engine compartment.
The power distribution box contains
high-current fuses that protect your
vehicle’s main electrical systems
from overloads.
Always disconnect the battery before servicing high current
fuses.
2007 07+ Explorer Sport Trac
(esp)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
243
To reduce risk of electrical shock, always replace the cover to
the Power Distribution Box before reconnecting the battery or
refilling fluid reservoirs.
If the battery has been disconnected and reconnected, refer to the
Battery
section of the
Maintenance and Specifications
chapter.
The high-current fuses are coded as follows:
Fuse/Relay
Location
Fuse Amp
Rating
Power Distribution Box
Description
1
50A**
BATT 2 (SJB)
2
50A**
BATT 3 (SJB)
3
50A**
BATT 1 (SJB)
4
30A**
Fuel pump, Fuel injectors
5
Not used
6
40A**
IVD module – pump
7
40A**
Powertrain Control Module
(PCM)
8
40A**
Heated windshield (left)
9
40A**
Heated windshield (right)
21
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
25
29
33
37
41
22
51
55
56
54
49
48
47
46B
46A
45B
45A
50B
50A
52
53
26
30
34
38
42
23
27
31
35
39
43
24
28
32
36
40
44
2007 07+ Explorer Sport Trac
(esp)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
244
Fuse/Relay
Location
Fuse Amp
Rating
Power Distribution Box
Description
10
20A**
Power down back window
11
30A**
Starter
12
Not used
13
30A**
Trailer tow battery charge
14
40A**
Power drivers seat
15
40A**
Not used
16
40A**
Blower motor
17
30A**
Trailer tow electronic brakes
18
Not used
19
Not used
20
Not used
21
20A*
Rear of console power point
22
20A*
Subwoofer
23
20A*
4x4 module
24
10A*
Powertrain Control Module
(PCM) KAP, CAN vent
25
20A*
Front of console power
point/Cigar lighter
26
20A*
4x4 module
27
20A*
6–speed transmission control
module (TCM)
28
20A*
Heated seats, Power mirror
29
20A*
Right high/low beam headlamp
30
20A*
Cargo bed power point
31
15A*
Fog lamps
32
5A*
Power mirrors
33
30A*
IVD module – valves
34
20A*
Left high/low beam headlamp
35
10A*
AC clutch
36
Not used
37
30A*
Front wiper
2007 07+ Explorer Sport Trac
(esp)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
245
Fuse/Relay
Location
Fuse Amp
Rating
Power Distribution Box
Description
38
15A*
5–speed transmission
39
15A*
PCM power
40
15A*
Fan clutch, PCV valve (4.0L
engine only), AC clutch relay
41
15A*
SDARs/DVD
42
15A*
Speed control deactivation
switch, EVMV, MAFS, HEGO,
EVR, CMS, (VCT1, VCT2, CMCV
on 4.6L only)
43
15A*
Coil on plug (4.6L engine), Coil
tower (4.0L engine)
44
15A*
Fuel injectors
45A
Not used
45B
Not used
46A
Not used
46B
Not used
47
Front wiper relay
48
PCM relay
49
Fuel pump relay
50A
Fog lamps relay
50B
AC clutch relay
51
Not used
52
A/C clutch diode
53
Not used
54
Trailer tow battery charge relay
55
Starter relay
56
Climate control blower relay
* Mini Fuses ** Cartridge Fuses
CHANGING THE TIRES
If you get a flat tire while driving:
do not brake heavily.
gradually decrease the vehicle’s speed.
2007 07+ Explorer Sport Trac
(esp)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
246
Place the provided height
adaptors onto the back of the
door as needed.
Close the door.
Press the depression in the door
to activate the transmitter.
AUXILIARY POWER POINT (12VDC)
Power outlets are designed for accessory plugs only. Do not insert
any other object in the power outlet as this will damage the
outlet and blow the fuse. Do not hang any type of accessory or
accessory bracket from the plug. Improper use of the power
outlet can cause damage not covered by your warranty.
The auxiliary power point is located
in the floor console.
Do not use the power point for
operating the cigarette lighter
element (if equipped).
To prevent the fuse from being
blown, do not use the power
point(s) over the vehicle capacity of
12 VDC/180W.
To prevent the battery from being
discharged, do not use the power point longer than necessary when the
engine is not running.
Always keep the power point caps closed when not being used.
Cigar/Cigarette lighter (if equipped)
Do not plug optional electrical accessories into the cigarette lighter
socket.
Do not hold the lighter in with your hand while it is heating, this will
damage the lighter element and socket. The lighter will be released from
its heating position when it is ready to be used.
Improper use of the lighter can cause damage not covered by your
warranty.
2007 07+ Explorer Sport Trac
(esp)
Owners Guide (post-2002-fmt)
USA
(fus)
Driver Controls
90
Never place your arm over the airbag module as a deploying
airbag can result in serious arm fractures or other injuries.
To properly position yourself away from the airbag:
Move your seat to the rear as far as you can while still reaching the
pedals comfortably.
Recline the seat slightly one or two degrees from the upright position.
Do not put anything on or over the airbag module. Placing
objects on or over the airbag inflation area may cause those
objects to be propelled by the airbag into your face and torso causing
serious injury.
Do not attempt to service, repair, or modify the airbag
supplemental restraint systems or its fuses. See your authorized
dealer.
Modifications to the front end of the vehicle, including frame,
bumper, front end body structure and non-Ford tow hooks may
effect the performance of the airbag sensors increasing the risk of
injury. Do not modify the front end of the vehicle with anything other
than authorized Ford accessories for your vehicle.
Additional equipment may affect the performance of the airbag
sensors increasing the risk of injury. Please refer to the
Body
Builders Layout Book
for instructions about the appropriate
installation of additional equipment.
2007 07+ Explorer Sport Trac
(esp)
Owners Guide (post-2002-fmt)
USA
(fus)
Seating and Safety Restraints
173
A difficulty with the system is indicated by one or more of the following:
The readiness light will either
flash or stay lit.
The readiness light will not
illuminate immediately after
ignition is turned on.
A series of five beeps will be heard. The tone pattern will repeat
periodically until the problem and/or light are repaired.
If any of these things happen, even intermittently, have the SRS serviced
at an authorized dealer immediately. Unless serviced, the system may not
function properly in the event of a collision.
Seat-mounted side airbag system
Do not place objects or mount equipment on or near the airbag
cover on the side of the seatbacks of the front seats or in front
seat areas that may come into contact with a deploying airbag. Failure
to follow these instructions may increase the risk of personal injury in
the event of a collision.
Do not use accessory seat covers. The use of accessory seat
covers may prevent the deployment of the side airbags and
increase the risk of injury in an accident.
Do not lean your head on the door. The side airbag could injure
you as it deploys from the side of the seatback.
Do not attempt to service, repair, or modify the airbag SRS, its
fuses or the seat cover on a seat containing an airbag. See your
authorized dealer.
All occupants of the vehicle should always wear their safety belts
even when an airbag SRS is provided.
How does the side airbag system work?
The design and development of the side airbag system included
recommended testing procedures that were developed by a group of
2007 07+ Explorer Sport Trac
(esp)
Owners Guide (post-2002-fmt)
USA
(fus)
Seating and Safety Restraints
181
Several air bag system components get hot after inflation. Do not
touch them after inflation.
If the side airbag has
deployed,
the airbag will
not function again. The side
airbag system (including the
seat) must be inspected and
serviced by an authorized
dealer .
If the airbag is not
replaced, the unrepaired area will
increase the risk of injury in a
collision.
Safety Canopy
´
system (if equipped)
Do not place objects or
mount equipment on or
near the headliner at the siderail
that may come into contact with a
deploying Safety Canopy
³
. Failure
to follow these instructions may
increase the risk of personal injury
in the event of a collision.
Do not lean your head on the door. The Safety Canopy
³
could
injure you as it deploys from the headliner.
Do not attempt to service, repair, or modify the Safety Canopy
³
system, its fuses, the A, B, or C pillar trim, or the headliner on a
vehicle containing a Safety Canopy
³
. See your authorized dealer.
All occupants of the vehicle including the driver should always
wear their safety belts even when an airbag SRS and Safety
Canopy
³
system is provided.
2007 07+ Explorer Sport Trac
(esp)
Owners Guide (post-2002-fmt)
USA
(fus)
Seating and Safety Restraints
183
2. Remove the rubber pad at the
bottom of the cup holder to locate
the access cap of the floor shifter
assembly.
3. Using a screwdriver (or
equivalent), remove the access
panel and depress the shifter lever
on the shift mechanism.
4. Apply the brake and shift into N (Neutral).
5. Return the cover plug to the console access hole. Start the vehicle.
If it is necessary to use the above procedure to move the gearshift lever,
it is possible that a fuse has blown or the vehicle’s brakelamps are not
operating properly. Refer to
Fuses and relays
in the
Roadside
Emergencies
chapter.
Do not drive your vehicle until you verify that the brakelamps
are working.
Always set the parking brake fully and make sure the gearshift is
latched in P (Park). Turn the ignition to the LOCK position and
remove the key whenever you leave your vehicle.
If the parking brake is fully released, but the brake warning lamp
remains illuminated, the brakes may not be working properly.
See your authorized dealer.
2007 07+ Explorer Sport Trac
(esp)
Owners Guide (post-2002-fmt)
USA
(fus)
Driving
247
FUSES AND RELAYS
Fuses
If electrical components in the
vehicle are not working, a fuse may
have blown. Blown fuses are
identified by a broken wire within
the fuse. Check the appropriate
fuses before replacing any electrical
components.
Note:
Always replace a fuse with one that has the specified amperage
rating. Using a fuse with a higher amperage rating can cause severe wire
damage and could start a fire.
Standard fuse amperage rating and color
COLOR
Fuse
rating
Mini fuses
Standard
fuses
Maxi fuses
Cartridge
maxi fuses
2A
Grey
Grey
3A
Violet
Violet
4A
Pink
Pink
5A
Tan
Tan
7.5A
Brown
Brown
10A
Red
Red
15A
Blue
Blue
20A
Yellow
Yellow
Yellow
Blue
25A
Natural
Natural
30A
Green
Green
Green
Pink
40A
Orange
Green
50A
Red
Red
60A
Blue
Yellow
70A
Tan
80A
Natural
15
2007 07+ Explorer Sport Trac
(esp)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
269
Passenger compartment fuse panel
The fuse panel is located below the
instrument panel on the driver’s
side.
To remove a fuse use the fuse puller tool provided on the fuse panel box.
The fuses are coded as follows:
Fuse/Relay
Location
Fuse Amp
Rating
Passenger Compartment Fuse
Panel Description
1
20A
Moon roof, Adjustable pedals
2
5A
Microcontroller power (SJB)
3
20A
Radio
4
10A
OBD II connector
5
5A
Moonroof, Power down back
window
6
20A
Door unlock/lock
CB1
4
3
2
1
8
7
6
5
12
11
10
9
16
15
14
13
20
19
18
17
24
23
22
21
28
27
26
25
2007 07+ Explorer Sport Trac
(esp)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
270
Fuse/Relay
Location
Fuse Amp
Rating
Passenger Compartment Fuse
Panel Description
7
15A
Trailer tow stop/turn lamps
8
15A
Ignition switch power, PATS
9
2A
6-speed transmission/PCM
(Ignition RUN/START), Fuel
pump relay
10
5A
Front wiper RUN/ACC (relay in
PDB)
11
5A
Radio start
12
5A
RUN accessory – Radio, Trailer
tow battery charge (relay in PDB)
13
15A
Heated mirror
14
20A
Horn
15
10A
Reverse lamps
16
10A
Trailer tow reverse lamps
17
10A
RUN/START – RCM (restraints),
PAD lamp, OCS module
18
10A
RUN/START – IVD switch, IVD,
4x4 module, 4x4 switch, Heated
seat switches, Compass,
Electrochromatic mirror, RSS
module
19
Not used
20
10A
RUN/START – Manual climate
control, DEATC, Brake shift
21
Not used
22
15A
Brake switch, Stop lamps, Turn
lamps
23
15A
Interior lamps, Puddle lamps,
Cargo lamp, Battery saver,
Instrument illumination
24
10A
Instrument cluster, Theft LED
25
15A
Trailer tow park lamps
2007 07+ Explorer Sport Trac
(esp)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
271
Fuse/Relay
Location
Fuse Amp
Rating
Passenger Compartment Fuse
Panel Description
26
15A
License plate lamps, Rear park
lamps, Front park lamps, Manual
climate control
27
15A
Not used
28
10A
Manual/DEATC climate control
CB1
25A
Windows
The following relays are located on either side of the passenger
compartment fuse panel. See your authorized dealer for service of these
relays.
Fuse/Relay Location
Description
Relay 1
Delayed ACC
Relay 2
Heated mirrors
Relay 3
Park lamps
Relay 4
RUN/START
Power distribution box
The power distribution box is
located in the engine compartment.
The power distribution box contains
high-current fuses that protect your
vehicle’s main electrical systems
from overloads.
Always disconnect the battery before servicing high current
fuses.
To reduce risk of electrical shock, always replace the cover to
the Power Distribution Box before reconnecting the battery or
refilling fluid reservoirs.
If the battery has been disconnected and reconnected, refer to the
Battery
section of the
Maintenance and Specifications
chapter.
2007 07+ Explorer Sport Trac
(esp)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
272
The high-current fuses are coded as follows:
Fuse/Relay
Location
Fuse Amp
Rating
Power Distribution Box
Description
1
50A**
BATT 2 (SJB)
2
50A**
BATT 3 (SJB)
3
50A**
BATT 1 (SJB)
4
30A**
Fuel pump, Fuel injectors
5
Not used
6
40A**
ABS pump
7
40A**
Powertrain Control Module
(PCM)
8
40A**
Heated windshield (left)
9
40A**
Heated windshield (right)
10
20A**
Power down back window
11
30A**
Starter
12
Not used
13
30A**
Trailer tow battery charge
14
40A**
Power drivers seat
2007 07+ Explorer Sport Trac
(esp)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
273
Fuse/Relay
Location
Fuse Amp
Rating
Power Distribution Box
Description
15
40A**
Heated mirror
16
40A**
Blower motor
17
30A**
Trailer tow electronic brakes
18
Not used
19
Not used
20
Not used
21
20A*
Rear of console power point
22
20A*
Subwoofer
23
20A*
4x4 module
24
10A*
Powertrain Control Module
(PCM) KAP, CAN vent
25
20A*
Front of console power
point/Cigar lighter
26
20A*
4x4 module
27
20A*
6–speed transmission control
module (TCM)
28
20A*
Heated seats, Power mirror
29
15A*
Right high/low beam headlamp
30
20A*
Cargo bed power point
31
15A*
Fog lamps
32
5A*
Power mirrors
33
30A*
ABS valves
34
15A*
Left high/low beam headlamp
35
10A*
AC clutch
36
Not used
37
30A*
Front wiper
38
15A*
5–speed transmission
39
15A*
PCM power
40
15A*
Fan clutch, PCV valve (4.0L
engine only), AC clutch relay
41
15A*
SDARs/DVD
2007 07+ Explorer Sport Trac
(esp)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
274
Fuse/Relay
Location
Fuse Amp
Rating
Power Distribution Box
Description
42
15A*
Speed control deactivation
switch, EVMV, MAFS, HEGO,
EVR, CMS, (VCT1, VCT2, CMCV
on 4.6L only)
43
15A*
Coil on plug (4.6L engine), Coil
tower (4.0L engine)
44
15A*
Fuel injectors
45B
Not used
45A
Not used
46B
Not used
46A
Not used
49
Fuel pump relay
50B
A/C clutch relay
50A
Fog lamps relay
51
Not used
52
A/C clutch diode
53
Not used
54
Trailer tow battery charge relay
55B
Front wiper relay
55A
PCM relay
56B
Starter relay
56A
Climate control blower relay
* Mini Fuses ** Cartridge Fuses
CHANGING THE TIRES
If you get a flat tire while driving:
do not brake heavily.
gradually decrease the vehicle’s speed.
hold the steering wheel firmly.
slowly move to a safe place on the side of the road.
Note:
The tire pressure monitoring system (TPMS) indicator light will
illuminate when the spare is in use. To restore the full functionality of
the monitoring system, all road wheels equipped with tire pressure
monitoring sensors must be mounted on the vehicle.
2007 07+ Explorer Sport Trac
(esp)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
275