Ford Escape Hybrid - 2012 Fuse Box Diagram

Ford Escape Hybrid - 2012 Fuse Box Diagram

The tray and inside bin can be
removed to open up space to fit a
laptop computer, MP3 players, CDs
or handbags. To remove, open the
console lid and pull the bin straight
up and out from the console
housing.
The sliding tray and inside bin can
be hooked on the side or rear of the
console for extra storage.
AUXILIARY POWER POINT (12V)
Power outlets are designed for accessory plugs only. Do not insert
any other object in the power outlet as this will damage the
outlet and blow the fuse. Do not hang any type of accessory or
accessory bracket from the plug. Improper use of the power
outlet can cause damage not covered by your warranty.
Auxiliary power points can be found in the following locations:
On the instrument panel
On the rear side of the center console
Do not use the power point for operating the cigarette lighter element (if
equipped).
Note:
Do not plug optional electrical accessories into the cigarette lighter
socket (if equipped). Improper use of the lighter can cause damage not
covered by your warranty, and can result in fire or serious injury.
Driver Controls
76
2012 Escape Hybrid
(ehv)
Owners Guide, 1st Printing
USA
(fus)
To prevent the fuse from being blown, do not use the power point(s)
over the vehicle capacity of 12V DC/180W. If the power point or cigar
lighter socket is not working, a fuse may have blown. Refer to
Fuses and
relays
in the
Roadside Emergencies
chapter for information on
checking and replacing fuses.
To have full capacity usage of your power point, the engine is required to
be running to avoid unintentional discharge of the battery. To prevent
the battery from being discharged:
do not use the power point longer than necessary when the engine is
not running,
do not leave battery chargers, video game adapters, computers and
other devices plugged in overnight or when the vehicle is parked for
extended periods.
Always keep the power point caps closed when not being used.
Power point (110V AC)
The 110V AC power point outlet is used for powering electrical devices
that require up to 150W. Exceeding the 150W limit will cause the power
point to cut off the power temporarily to provide overload protection.
Note:
The 110V AC power point is
equipped with a safety cap and a
safety twist tab. They both provide
protection from inserting any object
into the power point other than the
110V AC electrical device plug. The
safety cap should always be in a
closed position whenever the power
point outlet is not in use.
The 110V AC power point is located
in the floor console in front of the
gearshift.
The power outlet is not designed for the following electric appliances;
they may not work properly:
Cathode ray tube type televisions
Motor loads, such as vacuum cleaners, electric saws and other electric
power tools, compressor-driven refrigerators, etc.
Measuring devices, which process precise data, such as medical
equipment, measuring equipment, etc.
Other appliances requiring an extremely stable power supply:
microcomputer-controlled electric blankets, touch sensor lamps, etc.
Driver Controls
77
2012 Escape Hybrid
(ehv)
Owners Guide, 1st Printing
USA
(fus)
WARNING:
Never place your arm over the airbag module as a
deploying airbag can result in serious arm fractures or other
injuries.
To properly position yourself away from the airbag:
Move your seat to the rear as far as you can while still reaching the
pedals comfortably.
Recline the seat slightly one or two degrees from the upright position.
WARNING:
Do not put anything on or over the airbag module.
Placing objects on or over the airbag inflation area may cause
those objects to be propelled by the airbag into your face and torso
causing serious injury.
WARNING:
Do not attempt to service, repair, or modify the
airbag supplemental restraint systems or its fuses. Contact your
authorized dealer as soon as possible.
WARNING:
Modifications to the front end of the vehicle,
including frame, bumper, front end body structure, tow hooks
and B-pillar surrounding parts may affect the performance of the
airbag sensors increasing the risk of injury. Do not modify the front
end of the vehicle.
WARNING:
Additional equipment may affect the performance of
the airbag sensors increasing the risk of injury.
Seating and Safety Restraints
144
2012 Escape Hybrid
(ehv)
Owners Guide, 1st Printing
USA
(fus)
Seat-mounted side airbag system
WARNING:
Do not place objects or mount equipment on or
near the airbag cover on the side of the seatbacks of the front
seats or in front seat areas that may come into contact with a
deploying airbag. Failure to follow these instructions may increase the
risk of personal injury in the event of a collision.
WARNING:
Do not use accessory seat covers. The use of
accessory seat covers may prevent the deployment of the side
airbags and increase the risk of injury in an accident.
WARNING:
Do not lean your head on the door. The side airbag
could injure you as it deploys from the side of the seatback.
WARNING:
Do not attempt to service, repair, or modify the
airbag SRS, its fuses or the seat cover on a seat containing an
airbag. See an authorized dealer.
WARNING:
All occupants of the vehicle should always wear
their safety belts even when an airbag SRS is provided.
Seating and Safety Restraints
152
2012 Escape Hybrid
(ehv)
Owners Guide, 1st Printing
USA
(fus)
Safety Canopy
³
System
WARNING:
Do not place
objects or mount equipment
on or near the headliner at the
siderail that may come into
contact with a deploying Safety
Canopy
±
. Failure to follow these
instructions may increase the risk
of personal injury in the event of a
collision.
WARNING:
Do not lean your head on the door. The Safety
Canopy
±
could injure you as it deploys from the headliner.
WARNING:
Do not attempt to service, repair, or modify the
Safety Canopy
±
System, its fuses, the A, B, or C pillar trim, or
the headliner on a vehicle containing a Safety Canopy
±
. Contact your
authorized dealer as soon as possible.
WARNING:
All occupants of the vehicle including the driver
should always wear their safety belts even when an airbag SRS
and Safety Canopy
±
System is provided.
WARNING:
To reduce risk of injury, do not obstruct or place
objects in the deployment path of the inflatable Safety Canopy
±
.
Seating and Safety Restraints
155
2012 Escape Hybrid
(ehv)
Owners Guide, 1st Printing
USA
(fus)
WARNING:
Loaded vehicles, with a higher center of gravity,
may handle differently than unloaded vehicles. Do not overload
your vehicle and use extra precautions, such as driving at slower
speeds, avoiding abrupt steering changes and allowing for increased
stopping distance, when driving a heavily loaded vehicle. Over-loading
or loading the vehicle improperly can deteriorate handling capability
and contribute to loss of vehicle control and vehicle rollover.
BRAKE-SHIFT INTERLOCK
This vehicle is equipped with a brake-shift interlock feature that prevents
the gearshift lever from being moved from P (Park) when the ignition is
in the on position unless brake pedal is pressed.
If you cannot move the gearshift lever out of P (Park) with ignition in
the on position and the brake pedal pressed, it is possible that a fuse has
blown or the vehicle’s brake lamps are not operating properly. Refer to
Fuses and relays
in the
Roadside Emergencies
chapter.
If the fuse is not blown, perform the following procedure:
1. Apply the parking brake.
2. Using a screwdriver or similar
tool, carefully pry out the small
Brake Transmission Shift Interlock
(BTSI) cover cap located to the
right of the gearshift lever.
3. Press the brake pedal and then
start the vehicle.
4. Insert a screwdriver or similar
tool straight down into the access
hole and press downward while
pulling the gearshift lever out of the
P (Park) position and into the N
(Neutral) position.
5. Remove tool and reinstall BTSI cover cap.
6. Release the parking brake and drive normally.
Driving
226
2012 Escape Hybrid
(ehv)
Owners Guide, 1st Printing
USA
(fus)
To reset the switch(es):
1. Turn the ignition to the off position.
2. Check the fuel system for leaks.
3. If no leaks are apparent, reset the switch by pressing in on the reset
button. Both switches should be checked and reset.
4. Turn the ignition to the on position.
5. Wait a few seconds and return the key to the off position.
6. Make another check for leaks.
If you see or smell fuel, do not reset the fuel pump shut-off or try to
start your vehicle; you could injure yourself or others. Have all the
passengers get out of the vehicle and call the local fire department or a
towing service.
FUSES AND RELAYS
Fuses
If electrical components in the
vehicle are not working, a fuse may
have blown. Blown fuses are
identified by a broken wire within
the fuse. Check the appropriate
fuses before replacing any electrical
components.
Note:
Always replace a fuse with one that has the specified amperage
rating. Using a fuse with a higher amperage rating can cause severe wire
damage and could start a fire.
Standard fuse amperage rating and color
COLOR
Fuse
rating
Mini
fuses
Standard
fuses
Maxi
fuses
Cartridge
maxi
fuses
Fuse link
cartridge
2A
Grey
Grey
3A
Violet
Violet
4A
Pink
Pink
5A
Tan
Tan
7.5A
Brown
Brown
15
Roadside Emergencies
249
2012 Escape Hybrid
(ehv)
Owners Guide, 1st Printing
USA
(fus)
COLOR
Fuse
rating
Mini
fuses
Standard
fuses
Maxi
fuses
Cartridge
maxi
fuses
Fuse link
cartridge
10A
Red
Red
15A
Blue
Blue
20A
Yellow
Yellow
Yellow
Blue
Blue
25A
Natural
Natural
Natural
Natural
30A
Green
Green
Green
Pink
Pink
40A
Orange
Green
Green
50A
Red
Red
Red
60A
Blue
Yellow
Yellow
70A
Tan
Brown
80A
Natural
Black
Black
Passenger compartment fuse panel
The fuse panel is located on the
right-hand side of the center
console, by the instrument panel.
Remove the panel cover to access
the fuse cover. Press the tabs on the
top and bottom of the fuse cover to
remove.
Roadside Emergencies
250
2012 Escape Hybrid
(ehv)
Owners Guide, 1st Printing
USA
(fus)
The fuses are coded as follows:
Fuse/Relay
Location
Fuse Amp
Rating
Protected Circuits
1
30A
110V inverter
2
15A
Brake on/off switch
3
15A
SYNC
±
module
4
30A
Moon roof
5
10A
Brake-shift interlock (BSI),
Passenger compartment fuse
panel, Keypad illumination
6
20A
Turn signals, Stop lamps
7
10A
Low beam headlamps (left)
8
10A
Low beam headlamps (right)
9
15A
Interior lights
10
15A
Backlighting
11
10A
Four wheel drive
12
7.5A
Power mirror switch
13
5A
Not used (spare)
14
10A
FCIM (radio buttons), Front
display module, GPS module
Roadside Emergencies
251
2012 Escape Hybrid
(ehv)
Owners Guide, 1st Printing
USA
(fus)
Fuse/Relay
Location
Fuse Amp
Rating
Protected Circuits
15
10A
Climate control
16
15A
Not used (spare)
17
20A
All lock motor feeds, Liftgate
release, Liftglass release
18
20A
Heated seat
19
25A
Rear wiper
20
15A
Datalink
21
15A
Fog lamps
22
15A
Park lamps
23
15A
High beam headlamps
24
20A
Horn relay
25
10A
Demand lamps
26
10A
Instrument panel cluster
27
20A
Ignition switch
28
5A
Radio
29
5A
Instrument panel cluster
30
5A
Not used (spare)
31
10A
Restraints control module
32
10A
Rear video camera module
33
10A
Not used (spare)
34
5A
Not used (spare)
35
10A
Four wheel drive, Electronic
power assist steering (EPAS),
110V inverter module, Park aid
module, Active park assist module
36
5A
Passive anti-theft system (PATS)
transceiver
37
10A
Not used (spare)
38
20A
Subwoofer/Amp (premium radio)
39
20A
Radio, Radio amplifier
(navigation)
40
20A
Front power point
Roadside Emergencies
252
2012 Escape Hybrid
(ehv)
Owners Guide, 1st Printing
USA
(fus)
Fuse/Relay
Location
Fuse Amp
Rating
Protected Circuits
41
15A
Driver/passenger door lock
switches, Auto dimming mirror,
Compass, Ambient lighting, Moon
roof, Camera display in mirror
42
10A
Not used (spare)
43
10A
Rear wiper logic, Heated seats
relay, Instrument cluster
44
10A
Not used (spare)
45
5A
Front wiper logic, Blower motor
relay
46
7.5A
Occupant classification system
(OCS), Passenger airbag
deactivation indicator (PADI)
47
30A Circuit
Breaker
Power windows
48
Delayed accessory relay
Power distribution box
The power distribution box is located in the engine compartment. The
power distribution box contains high-current fuses that protect your
vehicle’s main electrical systems from overloads.
WARNING:
Always disconnect the low voltage (underhood)
battery before servicing high current fuses.
WARNING:
To reduce risk of electrical shock, always replace
the cover to the power distribution box before reconnecting the
low voltage (underhood) battery or refilling fluid reservoirs.
If the low voltage (underhood) battery has been disconnected and
reconnected, refer to the
Low voltage (underhood) battery
section of
the
Maintenance and Specifications
chapter.
Roadside Emergencies
253
2012 Escape Hybrid
(ehv)
Owners Guide, 1st Printing
USA
(fus)
The fuses are coded as follows.
Fuse/Relay
Location
Fuse Amp
Rating
Protected Circuits
A
80A Midi
Power steering control module
B
125A Midi
Passenger compartment fuse
panel
1
15A*
Heated mirror
2
30A**
Rear defroster
3
20A**
Rear power point
4
40A**
Electric vacuum pump
5
10A*
Powertrain control module (PCM)
– keep alive power, PCM relay,
Transmission control module,
Canister vent
6
Not used
7
15A*
Liftgate latch
8
5A*
Traction battery control module
9
50A**
Brake control module
10
30A**
Front wipers
11
Not used
12
40A**
Blower motor
13
Not used
Roadside Emergencies
254
2012 Escape Hybrid
(ehv)
Owners Guide, 1st Printing
USA
(fus)
Fuse/Relay
Location
Fuse Amp
Rating
Protected Circuits
14
10A*
Heater/Coolant pump
15
50A**
Traction battery control module
(TBCM)
16
40A**
Cooling fan 1
17
40A**
Cooling fan 2
18
50A**
Brake control module solenoid
19
30A**
Power seats
20
Not used
21A
Rear defroster relay
21B
Ignition relay
21C
Blower relay
21D
PCM relay
22
15A*
Ignition coils
23
15A*
Fuel injectors
24
10A*
Transmission control module
25
5A*
TBCM
26
20A*
Fuel pump, TBCM
27
10A*
PCM (general powertrain
components malfunction indicator
lamp), Heater pump relay, Motor
electronics coolant pump relay,
Electronic A/C compressor
28
15A*
Universal exhaust gas oxygen
(UEGO) sensor, PCM – emission
related powertrain components
malfunction indicator lamp
29
15A*
PCM power
30A
Cooling fan 1 relay
30B
Electric vacuum pump mechanical
relay
30C
Cooling fan main relay
30D
Cooling fan 2 relay
Roadside Emergencies
255
2012 Escape Hybrid
(ehv)
Owners Guide, 1st Printing
USA
(fus)
Fuse/Relay
Location
Fuse Amp
Rating
Protected Circuits
31A
Reverse lamp relay
31B
Not used
31C
Heater pump relay
31D
Coolant pump relay
31E
Not used
31F
Liftgate latch relay
32
Not used
33
PCM diode
34
Not used
35
10A*
Run/start, Reverse lamps, Rear
defrost relay
36
Not used
* Mini fuse ** Cartridge fuse
Roadside Emergencies
256
2012 Escape Hybrid
(ehv)
Owners Guide, 1st Printing
USA
(fus)
Auxiliary relay box
The relay box is located in the engine compartment on the radiator
support bracket.
Fuse/Relay
location
Fuse amp
rating
Description
Relay
Electric vacuum pump (solid state)
1
Not used
2
Not used
3
Not used
4
5A*
Vacuum pump monitor
5
Not used
6
Not used
* Mini fuses **Cartridge fuse
Roadside Emergencies
257
2012 Escape Hybrid
(ehv)
Owners Guide, 1st Printing
USA
(fus)