Ford E-250 - 2006 Fuse Box Diagram

Ford E-250 - 2006 Fuse Box Diagram

Drive the vehicle slowly (less than 5 km/h [3 mph]) in circles until
CAL indicator turns off in about 2–3 complete circles.
The compass is now calibrated.
AUXILIARY POWER POINT (12VDC)
Power outlets are designed for accessory plugs only. Do not insert
any other object in the power outlet as this will damage the
outlet and blow the fuse. Do not hang any type of accessory or
accessory bracket from the plug. Improper use of the power
outlet can cause damage not covered by your warranty.
The auxiliary power point is located
on the instrument panel.
A second power point (if equipped)
is located behind the driver’s seat on
the upper trim panel.
Do not use the power point for
operating the cigarette lighter
element (if equipped).
To prevent the fuse from being
blown, do not use the power
point(s) over the vehicle capacity of 12 VDC/180W.
To prevent the battery from being discharged, do not use the power
point longer than necessary when the engine is not running.
Always keep the power point caps closed when not being used.
Cigar/Cigarette lighter (if equipped)
Do not plug optional electrical accessories into the cigarette lighter
socket.
Do not hold the lighter in with your hand while it is heating, this will
damage the lighter element and socket. The lighter will be released from
its heating position when it is ready to be used.
Improper use of the lighter can cause damage not covered by your
warranty.
POWER WINDOWS (IF EQUIPPED)
Do not leave children unattended in the vehicle and do not let
children play with the power windows. They may seriously injure
themselves.
2006 Econoline
(eco)
Owners Guide (post-2002-fmt)
USA
(fus)
Driver Controls
47
The National Highway Traffic Safety Administration (NHTSA)
recommends a minimum distance of at least 25 cm (10 inches)
between an occupant’s chest and the driver airbag module.
Never place your arm over the air bag module as a deploying air
bag can result in serious arm fractures or other injuries.
To properly position yourself away from the airbag:
Move your seat to the rear as far as you can while still reaching the
pedals comfortably.
Recline the seat slightly one or two degrees from the upright position.
Do not put anything on or over the air bag module. Placing
objects on or over the air bag inflation area may cause those
objects to be propelled by the air bag into your face and torso causing
serious injury.
Do not attempt to service, repair, or modify the airbag
supplemental restraint systems or its fuses. See your Ford or
Lincoln Mercury dealer.
Modifying or adding equipment to the front end of the vehicle
(including frame, bumper, front end body structure and tow
hooks) may affect the performance of the airbag system, increasing the
risk of injury. Do not modify the front end of the vehicle.
Additional equipment may affect the performance of the airbag
sensors increasing the risk of injury. Please refer to the
Body
Builders Layout Book
for instructions about the appropriate
installation of additional equipment.
2006 Econoline
(eco)
Owners Guide (post-2002-fmt)
USA
(fus)
Seating and Safety Restraints
75
AUTOMATIC TRANSMISSION OPERATION
Brake-shift interlock
This vehicle is equipped with a brake-shift interlock feature that prevents
the gearshift lever from being moved from P (Park) when the ignition is
in the ON position unless brake pedal is depressed.
If you cannot move the gearshift lever out of P (Park) with ignition in
the ON position and the brake pedal depressed:
1. Apply the parking brake, turn ignition key to LOCK, then remove the
key.
2. Insert the key and turn it to OFF.
Apply the brake pedal and shift
to N (Neutral)
.
When the key is in the ignition and in the OFF position, the
automatic transmission shift lever can be moved from the P
(Park) position without the brake pedal depressed. To avoid unwanted
vehicle movement, always set the parking brake.
3. Start the vehicle.
If it is necessary to use the above procedure to move the gearshift lever,
it is possible that a fuse has blown or the vehicle’s brakelamps are not
operating properly. Refer to
Fuses and relays
in the
Roadside
Emergencies
chapter.
Do not drive your vehicle until you verify that the brakelamps
are working.
Always set the parking brake fully and make sure the gearshift is
latched in P (Park). Turn the ignition to the LOCK position and
remove the key whenever you leave your vehicle.
If the parking brake is fully released, but the brake warning lamp
remains illuminated, the brakes may not be working properly.
See your dealer or a qualified service technician as soon as possible.
2006 Econoline
(eco)
Owners Guide (post-2002-fmt)
USA
(fus)
Driving
146
On commercial stripped chassis
vehicles, this switch is located on a
bracket above the brake pedal.
To reset the switch:
1. Turn the ignition OFF.
2. Check the fuel system for leaks.
3. If no leaks are apparent, reset the
switch by pushing in on the reset
button.
4. Turn the ignition ON.
5. Wait a few seconds and return
the key to OFF.
6. Make another check for leaks.
FUSES AND RELAYS
Fuses
If electrical components in the
vehicle are not working, a fuse may
have blown. Blown fuses are
identified by a broken wire within
the fuse. Check the appropriate
fuses before replacing any electrical
components.
Note:
Always replace a fuse with one that has the specified amperage
rating. Using a fuse with a higher amperage rating can cause severe wire
damage and could start a fire.
15
2006 Econoline
(eco)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
159
Standard fuse amperage rating and color
COLOR
Fuse
rating
Mini
fuses
Standard
fuses
Maxi
fuses
Cartridge
maxi
fuses
Fuse link
cartridge
2A
Grey
Grey
3A
Violet
Violet
4A
Pink
Pink
5A
Tan
Tan
7.5A
Brown
Brown
10A
Red
Red
15A
Blue
Blue
20A
Yellow
Yellow
Yellow
Blue
Blue
25A
Natural
Natural
30A
Green
Green
Green
Pink
Pink
40A
Orange
Green
Green
50A
Red
Red
Red
60A
Blue
Yellow
70A
Tan
Brown
80A
Natural
Black
Passenger compartment fuse panel
The fuse panel is located below and to the left of the steering wheel by
the brake pedal. Remove the panel cover to access the fuses.
To remove a fuse use the fuse puller tool provided on the fuse panel
cover.
2006 Econoline
(eco)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
160
The fuses are coded as follows.
Fuse/Relay
Location
Fuse Amp
Rating
Passenger Compartment Fuse
Panel Description
1
5A
4–Wheel Anti–lock Brake System
(4WABS) module
2
10A
Remote Keyless Entry (RKE), O/D
cancel, IVD module
3
15A
Trip computer, Radio, Overhead
console
4
15A
Courtesy lamps
5
30A
Power lock switches, Power locks
without RKE
6
10A
Brake-shift interlock, Daytime
Running Lamps (DRL) module
7
10A
Multi-function switch, Turn signals
1
2
3
4
5
7
6
8
9
10
11
42
43
44
13
12
14
15
16
17
19
18
20
21
22
23
25
24
26
27
28
29
31
30
32
33
34
35
37
36
38
39
40
41
2006 Econoline
(eco)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
161
Fuse/Relay
Location
Fuse Amp
Rating
Passenger Compartment Fuse
Panel Description
8
30A
Radio capacitor(s), Ignition coil,
Powertrain Control Module (PCM)
diode, PCM power relay
9
5A
Wiper control module
10
20A
Main light switch, Park lamps,
License lamp (external lamps),
Multi-function switch (flash-to-pass)
11
15A
Multi-function switch (hazards),
Brake lamp switch, Brake lamps
12
15A
Back-up lamps, Auxiliary battery
relay (gasoline engine only)
13
15A
Blend door actuator, Function
selector switch
14
5A
Instrument cluster
15
5A
Trailer battery charge relay, Cluster
16
30A
Power seats
17
5A
Power mirrors
18
Not used
19
Not used
20
10A
Restraints
21
Not used
22
15A
Memory power radio, Battery saver
relay, Instrument cluster, Courtesy
lamp relay, Accessory delay relay
23
20A
Power locks w/RKE
24
Not used
25
10A
Left headlamp (low beam)
26
20A
Cigar lighter, Diagnostics
27
5A
Radio
28
Not used
29
Not used
30
15A
Headlamps (high beam indicator)
31
10A
Right headlamp (low beam)
2006 Econoline
(eco)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
162
Fuse/Relay
Location
Fuse Amp
Rating
Passenger Compartment Fuse
Panel Description
32
20A
Power point #1 (instrument panel)
33
10A
Start relay
34
Not used
35
Not used
36
5A
Instrument illumination
37
Not used
38
Not used
39
10A
Trailer tow electric brake, Center
High-Mounted Stop Lamp (CHMSL),
Brake lamps
40
20A
Power point #2 (2nd row seating
position - driver side)
41
30A
Modified vehicle
42
20A circuit
breaker
Power windows
43
Not used
44
20A circuit
breaker
Wiper/washer
Power distribution box
The power distribution box is located in the engine compartment. The
power distribution box contains high-current fuses that protect your
vehicle’s main electrical systems from overloads.
Always disconnect the battery before servicing high current
fuses.
To reduce risk of electrical shock, always replace the cover to
the Power Distribution Box before reconnecting the battery or
refilling fluid reservoirs.
If the battery has been disconnected and reconnected, refer to the
Battery
section of the
Maintenance and Specifications
chapter.
2006 Econoline
(eco)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
163
The high-current fuses are coded as follows.
Fuse/Relay
Location
Fuse Amp
Rating
Power Distribution Box
Description
1
Powertrain Control Module (PCM)
diode
2
Not used
3
10A*
Daytime Running Lamps (DRL)
module, A/C clutch
4
5A*
Heated PCV (4.6L and 6.8L gasoline
engines)
5
15A*
Horn relay
6
2A*
Brake pressure switch
7
60A**
Ignition switch, Accessory delay
8
40A**
Trailer battery charge relay
9
50A**
Modified vehicle power
10
30A**
Electric brake controller
11
60A**
4-Wheel Anti-lock Brake System
(4WABS)
12
60A**
I/P fuses 29, 34, 35, 40 and 41
2006 Econoline
(eco)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
164
Fuse/Relay
Location
Fuse Amp
Rating
Power Distribution Box
Description
13
20A**
Fuel pump relay
14
50A**
Auxiliary blower relay
15
30A**
Main light switch
16
20A**
Injectors (gasoline engines)
17
50A**
Blower motor relay (blower motor)
18
60A**
Engine compartment fuses 3, 5 and
26, Instrument panel fuses 26 and
32, Start relay
19
50A**
IDM relay (diesel engine only)
40A**
IVD (gasoline engines only )
20
60A**
Auxiliary battery relay (gasoline
engine only), PDB fuses 8 and 24
21
30A**
PCM power relay, PDB fuse 27
22
60A**
I/P fuses 4, 5, 10, 11, 16, 17, 22 and
23, Circuit breaker 44
23
10A*
Alternator field (diesel engine only)
20A*
CMS, HEGOS, MAF, EGR, A/C
clutch relay (gasoline engine only)
24
20A*
Trailer tow running lamps and
back-up lamp relays
25
Not used
26
20A*
Trailer tow turn signals
27
10A*
PCM
28
Not used
A
Fuel pump relay
B
Horn relay
C
Trailer back-up lamps relay
D
Trailer running lamps relay
E
Trailer battery charge relay
F
IDM relay (diesel only), IVD
(gasoline only)
G
PCM relay
2006 Econoline
(eco)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
165
Fuse/Relay
Location
Fuse Amp
Rating
Power Distribution Box
Description
H
Blower motor relay
J
Accessory delay relay
K
Start relay
* Mini fuses ** Maxi fuses
Relay modules
Instrument panel relay module
The instrument panel relay module is located behind the radio in the
center of the instrument panel. Have a certified technician or your dealer
service this module, if required.
The relays are coded as follows:
Relay location
Description
1
Interior lamps
2
Open
3
Open
4
Battery saver
2006 Econoline
(eco)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
166
3. Press and hold the SELECT
control until VAR appears in the
display, then release. The display
should show the current zone
number.
4. Press the SELECT control until
the desired zone number appears.
The display will flash and then
return to normal operation. The zone is now updated.
Compass calibration adjustment
Perform this adjustment in an open
area free from steel structures and
high voltage lines:
Press and hold the SELECT
control until CAL appears in the
display (approximately eight
seconds) and release.
Drive the vehicle slowly (less
than 5 km/h [3 mph]) in circles until CAL indicator turns off in about
2–3 complete circles.
The compass is now calibrated.
AUXILIARY POWER POINT (12VDC)
Power outlets are designed for accessory plugs only. Do not insert
any other object in the power outlet as this will damage the
outlet and blow the fuse. Do not hang any type of accessory or
accessory bracket from the plug. Improper use of the power
outlet can cause damage not covered by your warranty.
The auxiliary power point is located
on the instrument panel.
A second power point (if equipped)
is located behind the driver’s seat on
the upper trim panel.
Do not use the power point for
operating the cigarette lighter
element (if equipped).
To prevent the fuse from being
blown, do not use the power
point(s) over the vehicle capacity of 12 VDC/180W.
9
VAR
CAL
2006 Econoline
(eco)
Owners Guide (post-2002-fmt)
USA
(fus)
Driver Controls
47
Do not put anything on or over the air bag module. Placing
objects on or over the air bag inflation area may cause those
objects to be propelled by the air bag into your face and torso causing
serious injury.
Do not attempt to service, repair, or modify the airbag
supplemental restraint systems or its fuses. See your authorized
dealer.
Modifying or adding equipment to the front end of the vehicle
(including frame, bumper, front end body structure and tow
hooks) may affect the performance of the airbag system, increasing the
risk of injury. Do not modify the front end of the vehicle.
Additional equipment may affect the performance of the airbag
sensors increasing the risk of injury. Please refer to the
Body
Builders Layout Book
for instructions about the appropriate
installation of additional equipment.
Children and airbags
Children must always be properly
restrained. Accident statistics
suggest that children are safer when
properly restrained in the rear
seating positions than in the front
seating position. Failure to follow
these instructions may increase the
risk of injury in a collision.
Airbags can kill or injure a
child in a child seat.
NEVER
place a rear-facing child
seat in front of an active airbag. If
you must use a forward-facing
child seat in the front seat, move
the seat all the way back.
2006 Econoline
(eco)
Owners Guide (post-2002-fmt)
USA
(fus)
Seating and Safety Restraints
77
AUTOMATIC TRANSMISSION OPERATION
Brake-shift interlock
This vehicle is equipped with a brake-shift interlock feature that prevents
the gearshift lever from being moved from P (Park) when the ignition is
in the ON position unless brake pedal is depressed.
If you cannot move the gearshift lever out of P (Park) with ignition in
the ON position and the brake pedal depressed:
1. Apply the parking brake, turn ignition key to LOCK, then remove the
key.
2. Insert the key and turn it to OFF.
Apply the brake pedal and shift
to N (Neutral)
.
When the key is in the ignition and in the OFF position, the
automatic transmission shift lever can be moved from the P
(Park) position without the brake pedal depressed. To avoid unwanted
vehicle movement, always set the parking brake.
3. Start the vehicle.
If it is necessary to use the above procedure to move the gearshift lever,
it is possible that a fuse has blown or the vehicle’s brakelamps are not
operating properly. Refer to
Fuses and relays
in the
Roadside
Emergencies
chapter.
Do not drive your vehicle until you verify that the brakelamps
are working.
Always set the parking brake fully and make sure the gearshift is
latched in P (Park). Turn the ignition to the LOCK position and
remove the key whenever you leave your vehicle.
If the parking brake is fully released, but the brake warning lamp
remains illuminated, the brakes may not be working properly.
See your authorized dealer as soon as possible.
2006 Econoline
(eco)
Owners Guide (post-2002-fmt)
USA
(fus)
Driving
150
FUSES AND RELAYS
Fuses
If electrical components in the
vehicle are not working, a fuse may
have blown. Blown fuses are
identified by a broken wire within
the fuse. Check the appropriate
fuses before replacing any electrical
components.
Note:
Always replace a fuse with one that has the specified amperage
rating. Using a fuse with a higher amperage rating can cause severe wire
damage and could start a fire.
Standard fuse amperage rating and color
COLOR
Fuse
rating
Mini
fuses
Standard
fuses
Maxi
fuses
Cartridge
maxi
fuses
Fuse link
cartridge
2A
Grey
Grey
3A
Violet
Violet
4A
Pink
Pink
5A
Tan
Tan
7.5A
Brown
Brown
10A
Red
Red
15A
Blue
Blue
20A
Yellow
Yellow
Yellow
Blue
Blue
25A
Natural
Natural
30A
Green
Green
Green
Pink
Pink
40A
Orange
Green
Green
50A
Red
Red
Red
60A
Blue
Yellow
70A
Tan
Brown
80A
Natural
Black
Passenger compartment fuse panel
The fuse panel is located below and to the left of the steering wheel by
the brake pedal. Remove the panel cover to access the fuses.
15
2006 Econoline
(eco)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
164
To remove a fuse use the fuse puller tool provided on the fuse panel
cover.
The fuses are coded as follows.
Fuse/Relay
Location
Fuse Amp
Rating
Passenger Compartment Fuse
Panel Description
1
5A
4–Wheel Anti–lock Brake System
(4WABS) module
2
10A
Remote Keyless Entry (RKE),
O/D cancel, IVD module
3
15A
Trip computer, Radio, Overhead
console
4
15A
Courtesy lamps
5
30A
Power lock switches, Power locks
without RKE
6
10A
Brake-shift interlock, Daytime
Running Lamps (DRL) module
1
2
3
4
5
7
6
8
9
10
11
42
43
44
13
12
14
15
16
17
19
18
20
21
22
23
25
24
26
27
28
29
31
30
32
33
34
35
37
36
38
39
40
41
2006 Econoline
(eco)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
165
Fuse/Relay
Location
Fuse Amp
Rating
Passenger Compartment Fuse
Panel Description
7
10A
Multi-function switch, Turn signals
8
30A
Radio capacitor(s), Ignition coil,
Powertrain Control Module (PCM)
diode, PCM power relay
9
5A
Wiper control module
10
20A
Main light switch, Park lamps,
License lamp (external lamps),
Multi-function switch
(flash-to-pass)
11
15A
Multi-function switch (hazards),
Brake lamp switch, Brake lamps
12
15A
Back-up lamps, Auxiliary battery
relay (gasoline engine only)
13
15A
Blend door actuator, Function
selector switch
14
5A
Instrument cluster
15
5A
Trailer battery charge relay,
Cluster
16
30A
Power seats
17
5A
Power mirrors
18
Not used
19
Not used
20
10A
Restraints
21
Not used
22
15A
Memory power radio, Battery
saver relay, Instrument cluster,
Courtesy lamp relay, Accessory
delay relay
23
20A
Power locks w/RKE
24
Not used
25
10A
Left headlamp (low beam)
26
20A
Cigar lighter, Diagnostics
2006 Econoline
(eco)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
166
Fuse/Relay
Location
Fuse Amp
Rating
Passenger Compartment Fuse
Panel Description
27
5A
Radio
28
Not used
29
Not used
30
15A
Headlamps (high beam indicator)
31
10A
Right headlamp (low beam)
32
20A
Power point #1 (instrument
panel)
33
10A
Start relay
34
30A
IP Body builder connector #3
35
Not used
36
5A
Instrument illumination
37
5A
Airbag deactivation switch
38
Not used
39
10A
Trailer tow electric brake, Center
High-Mounted Stop Lamp
(CHMSL), Brake lamps
40
20A
Power point #2 (2nd row seating
position - driver side)
41
30A
Modified vehicle
42
20A circuit
breaker
Power windows
43
Not used
44
20A circuit
breaker
Wiper/washer
Power distribution box
The power distribution box is located in the engine compartment. The
power distribution box contains high-current fuses that protect your
vehicle’s main electrical systems from overloads.
Always disconnect the battery before servicing high current
fuses.
2006 Econoline
(eco)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
167
To reduce risk of electrical shock, always replace the cover to
the Power Distribution Box before reconnecting the battery or
refilling fluid reservoirs.
If the battery has been disconnected and reconnected, refer to the
Battery
section of the
Maintenance and Specifications
chapter.
The high-current fuses are coded as follows.
Fuse/Relay
Location
Fuse Amp
Rating
Power Distribution Box
Description
1
Powertrain Control Module (PCM)
diode
2
Auxiliary battery diode
3
15A*
Daytime Running Lamps (DRL)
module, A/C clutch
4
5A*
Heated PCV (4.6L and 6.8L
gasoline engines)
5
15A*
Horn relay
6
2A*
Brake pressure switch
7
60A**
Ignition switch, Accessory delay
2006 Econoline
(eco)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
168
Fuse/Relay
Location
Fuse Amp
Rating
Power Distribution Box
Description
8
40A**
Trailer battery charge relay
9
50A**
Modified vehicle power
10
30A**
Electric brake controller
11
60A**
4-Wheel Anti-lock Brake System
(4WABS)
40A**
AdvanceTrac
±
with RSC
12
60A**
I/P fuses 29, 34, 35, 40 and 41
13
20A**
Fuel pump relay
14
50A**
Auxiliary blower relay
15
30A**
Main light switch
16
20A**
Injectors (gasoline engines)
17
50A**
Blower motor relay (blower
motor)
18
60A**
Engine compartment fuses 3, 5
and 26, Instrument panel fuses 26
and 32, Start relay
19
50A**
IDM relay (diesel engine only)
40A**
AdvanceTrac
±
with RSC (gasoline
engines only )
20
60A**
Auxiliary battery relay (gasoline
engine only), PDB fuses 8 and 24
21
30A**
PCM power relay, PDB fuse 27
22
60A**
I/P fuses 4, 5, 10, 11, 16, 17, 22
and 23, Circuit breaker 44
23
10A*
Alternator field (diesel engine
only)
20A*
CMS, HEGOS, MAF, EGR, A/C
clutch relay (gasoline engine
only)
24
20A*
Trailer tow running lamps and
back-up lamp relays
25
Not used
2006 Econoline
(eco)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
169
Fuse/Relay
Location
Fuse Amp
Rating
Power Distribution Box
Description
26
20A*
Trailer tow turn signals
27
10A*
PCM
28
Not used
A
Fuel pump relay
B
Horn relay
C
Trailer back-up lamps relay
D
Trailer running lamps relay
E
Trailer battery charge relay
F
IDM relay (diesel only), IVD
(gasoline only)
G
PCM relay
H
Blower motor relay
J
Accessory delay relay
K
Start relay
* Mini fuses ** Maxi fuses
Relay modules
Instrument panel relay module
The instrument panel relay module is located behind the radio in the
center of the instrument panel. Have your authorized dealer service this
module, if required.
The relays are coded as follows:
2006 Econoline
(eco)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
170