Ford Crown Victoria - 2009 Fuse Box Diagram

Ford Crown Victoria - 2009 Fuse Box Diagram

Cupholders
Air vents to the rear seating positions (heat only)
WARNING:
Use only soft cups in the cupholder. Hard objects
can injure you in a collision.
AUXILIARY POWER POINT (12VDC)
Power outlets are designed for accessory plugs only. Do not insert
any other object in the power outlet as this will damage the
outlet and blow the fuse. Do not hang any type of accessory or
accessory bracket from the plug. Improper use of the power
outlet can cause damage not covered by your warranty.
The auxiliary power point is located under the cup holder and ashtray
drawer in the center stack. The auxiliary power point for five passenger
vehicles is located in the floor console storage bin.
Do not use the power point for operating the cigarette lighter element (if
equipped).
To prevent the fuse from being blown, do not use the power point(s)
over the vehicle capacity of 12 VDC/180W. If the power point or cigar
lighter socket is not working, a fuse may have blown. Refer to
Fuses and
relays
in the
Roadside Emergencies
chapter for information on
checking and replacing fuses.
To have full capacity usage of your power point, the engine is required to
be running to avoid unintentional discharge of the battery. To prevent
the battery from being discharged:
do not use the power point longer than necessary when the engine is
not running,
do not leave battery chargers, video game adapters, computers and
other devices plugged in overnight or when the vehicle is parked for
extended periods.
Always keep the power point caps closed when not being used.
Cigar/Cigarette lighter (if equipped)
Do not plug optional electrical accessories into the cigarette lighter socket.
Do not hold the lighter in with your hand while it is heating, this will
damage the lighter element and socket. The lighter will be released from
its heating position when it is ready to be used.
Note:
Improper use of the lighter can cause damage not covered by your
warranty, and can result in fire or serious injury.
2009 Crown Victoria
(cro)
Owners Guide, 1st Printing
USA
(fus)
Driver Controls
52
WARNING:
The National Highway Traffic Safety Administration
(NHTSA) recommends a minimum distance of at least 10 inches
(25 cm) between an occupant’s chest and the driver airbag module.
WARNING:
Never place your arm over the air bag module as a
deploying air bag can result in serious arm fractures or other
injuries.
WARNING:
Ford Motor Company recommends that an
authorized dealer inspect all steering column assemblies in use
in vehicles involved in a collision. Failure to inspect and if necessary
replace the steering column assembly could result in severe injury or
death in the event of a collision.
WARNING:
Do not attempt to service, repair, or modify the
steering column, its adaptive module, or its fuses. See your
authorized dealer.
To properly position yourself away from the airbag:
Move your seat to the rear as far as you can while still reaching the
pedals comfortably.
Recline the seat slightly one or two degrees from the upright position.
WARNING:
Do not put anything on or over the air bag module.
Placing objects on or over the air bag inflation area may cause
those objects to be propelled by the air bag into your face and torso
causing serious injury.
WARNING:
Do not attempt to service, repair, or modify the
airbag supplemental restraint systems or its fuses. See your
authorized dealer.
WARNING:
The front passenger airbag is not designed to offer
protection to an occupant in the center front seating position.
2009 Crown Victoria
(cro)
Owners Guide, 1st Printing
USA
(fus)
Seating and Safety Restraints
105
WARNING:
Do not use accessory seat covers. The use of
accessory seat covers may prevent the deployment of the side
airbags and increase the risk of injury in an accident.
WARNING:
Do not lean your head on the door. The side airbag
could injure you as it deploys from the side of the seatback.
WARNING:
Do not attempt to service, repair, or modify the
airbag SRS, its fuses or the seat cover on a seat containing an
airbag. See your authorized dealer.
WARNING:
All occupants of the vehicle should always wear
their safety belts even when an airbag SRS is provided.
How does the side airbag system work?
The design and development of the
side airbag system included
recommended testing procedures
that were developed by a group of
automotive safety experts known as
the Side Airbag Technical Working
Group. These recommended testing
procedures help reduce the risk of
injuries related to the deployment of
side airbags.
The side airbag system consists of
the following:
An inflatable nylon bag (airbag)
with a gas generator concealed
behind the outboard bolster of
the driver and front passenger
seatbacks.
A special seat cover designed to allow airbag deployment.
The same warning light, electronic control and diagnostic unit as used
for the front airbags.
Two crash sensors located near the side of the vehicle.
Side airbags, in combination with safety belts, can help reduce the risk of
severe injuries in the event of a significant side impact collision.
2009 Crown Victoria
(cro)
Owners Guide, 1st Printing
USA
(fus)
Seating and Safety Restraints
114
If you exceed the load limit, the rear air suspension may not operate.
The air suspension shut-off switch is
located on the left side of the trunk.
If this switch is in the off position,
the rear air suspension will not
operate.
WARNING:
On vehicles
equipped with air
suspension, turn off the air
suspension switch prior to jacking,
hoisting or towing your vehicle.
Normal vehicle operation does not
require any action by the driver.
TRACTION-LOK™ AXLE (IF EQUIPPED)
This axle provides added traction on slippery surfaces, particularly when
one wheel is on a poor traction surface. Under normal conditions, the
Traction-Lok™ axle functions like a standard rear axle.
Extended use of other than the manufacturer’s specified size tires on a
Traction-Lok™ rear axle could result in a permanent reduction in
effectiveness. This loss of effectiveness does not affect normal driving
and should not be noticeable to the driver.
AUTOMATIC TRANSMISSION OPERATION
Brake-shift interlock
This vehicle is equipped with a brake-shift interlock feature that prevents
the gearshift lever from being moved from P (Park) when the ignition is
in the on position unless brake pedal is depressed.
If you cannot move the gearshift lever out of P (Park) with ignition in
the on position and the brake pedal depressed, it is possible that a fuse
has blown or the vehicle’s brakelamps are not operating properly. Refer
to
Fuses and relays
in the
Roadside Emergencies
chapter.
If the fuse is not blown, perform the following procedure:
1. Apply the parking brake, turn the ignition to 2 (Accessory).
AIR SUSPENSION
SWITCH
INTERRUPTEUR DE
LA SUSPENSION
PNEUMATIQUE
WARNING
AVERTISSEMENT
OFF-ARRET
To prevent sudden
vehicle movement,
turn off air suspen-
sion switch prior to
jacking, hoisting or
towing vehicle.
Pour prévenir tout mouvement soudain du véhi-
cule, placer à l'arrêt l'interrupteur de la suspension
pneumatique avant de lever le véhicule (cric ou
pont élévateur) ou de le remorquer.
OFF
2009 Crown Victoria
(cro)
Owners Guide, 1st Printing
USA
(fus)
Driving
175
3. If no fuel leak is apparent, reset the fuel pump shut-off switch by
pushing in on the reset button.
4. Turn the ignition to the on position. Pause for a few seconds and
return the key to the OFF position.
5. Make a further check for leaks in the fuel system.
FUSES AND RELAYS
Fuses
If electrical components in the
vehicle are not working, a fuse may
have blown. Blown fuses are
identified by a broken wire within
the fuse. Check the appropriate
fuses before replacing any electrical
components.
Note:
Always replace a fuse with one that has the specified amperage
rating. Using a fuse with a higher amperage rating can cause severe wire
damage and could start a fire.
Standard fuse amperage rating and color
COLOR
Fuse
rating
Mini
fuses
Standard
fuses
Maxi
fuses
Cartridge
maxi
fuses
Fuse link
cartridge
2A
Grey
Grey
3A
Violet
Violet
4A
Pink
Pink
5A
Tan
Tan
7.5A
Brown
Brown
10A
Red
Red
15A
Blue
Blue
20A
Yellow
Yellow
Yellow
Blue
Blue
25A
Natural
Natural
30A
Green
Green
Green
Pink
Pink
40A
Orange
Green
Green
15
2009 Crown Victoria
(cro)
Owners Guide, 1st Printing
USA
(fus)
Roadside Emergencies
183
COLOR
Fuse
rating
Mini
fuses
Standard
fuses
Maxi
fuses
Cartridge
maxi
fuses
Fuse link
cartridge
50A
Red
Red
Red
60A
Blue
Yellow
Yellow
70A
Tan
Brown
80A
Natural
Black
Black
Passenger compartment fuse panel
The fuse panel is located below and to the left of the steering wheel by
the brake pedal. Remove the panel cover to access the fuses.
To remove a fuse use the fuse puller tool provided on the fuse panel
cover.
The fuses are coded as follows.
27
25
26
24
23
21
22
19
20
18
16
17
15
14
12
13
10
33
31
29
32
30
28
11
9
7
8
6
5
3
4
1
2
Relay
1
2009 Crown Victoria
(cro)
Owners Guide, 1st Printing
USA
(fus)
Roadside Emergencies
184
Fuse/Relay
Location
Fuse Amp
Rating
Protected Circuits
1
10A
Ignition (START) - Starter relay
coil, DTRS
2
7.5A
Power mirrors, Mirror switch,
Keypad switch, Decklid switch,
DDM, Cluster
3
5A
Ignition (START) - Audio mute,
Police PDB (Police vehicles only)
4
10A
LCM (switch illumination),
Autolamp sensor
5
7.5A
Ignition (ON/ACC) - LCM
6
7.5A
LCM
7
10A
Ignition (ON/ACC) - Wiper
module
8
10A
Electronic Automatic Temperature
Control (EATC) module (vehicles
equipped with EATC only)
9
7.5A
Ignition (ON/ACC) - Door lock
switch illumination, Heated seat
switch illumination, Radio,
Antenna, Electrochromatic mirror,
Window relay coil (non-Police
vehicles only), Window and
decklid relay coil and Police
ON/ACC relay coil (Police vehicles
only)
10
15A
Hazards (non-Police vehicles
only)
20A
Hazards (Police vehicles only)
11
15A
Ignition (ON) - Turn signals
12
15A
Audio
13
10A
Ignition (ON) - Rear Air
Suspension Module (RASM),
Cluster
2009 Crown Victoria
(cro)
Owners Guide, 1st Printing
USA
(fus)
Roadside Emergencies
185
Fuse/Relay
Location
Fuse Amp
Rating
Protected Circuits
14
15A
Taxi, Adjustable pedals
15
10A
Ignition (ON) - EATC module,
A/C mode switch (vehicles
equipped with manual A/C only),
A/C blower relay coil
16
20A
OBD II
17
10A
Ignition (ON) - A/C mode switch
(vehicles equipped with manual
A/C), Blend door, Heated seat
modules
18
15A
Lighting control module (interior
lighting)
19
10A
LCM (Left-hand low beam)
20
10A
Ignition (ON/START) - Back-up
lamps, Anti-lock Brake system
(ABS)
21
10A
LCM (Right-hand low beam)
22
10A
Ignition (ON/START) - Restraint
Control Module (RCM), Occupant
Classification Sensor (OCS),
Passenger Airbag Deactivation
Indicator (PADI)
23
15A
Multi-function switch
(Flash-to-pass), LCM (High
beams)
24
10A
Ignition (ON/START) - Passive
Anti-Theft System (PATS)
module, Powertrain Control
Module (PCM) relay coil, Fuel
relay coil, Ignition relay coil
25
15A
LCM (Park lamps, license lamps)
2009 Crown Victoria
(cro)
Owners Guide, 1st Printing
USA
(fus)
Roadside Emergencies
186
Fuse/Relay
Location
Fuse Amp
Rating
Protected Circuits
26
10A
Ignition (ON/START) - Cluster,
LCM, Overdrive cancel switch,
Traction control switch
27
Not used
28
7.5A
Brake signal, LCM (BTSI), ABS
29
2A
Hazard in (Police vehicles only)
30
2A
Battery saver (Police vehicles
only)
31
5A
Key in (LCM)
32
2A
Hazard out (Police vehicles only)
33
10A
Fire suppression module (if
equipped) (Police vehicles only)
Relay 1
Full ISO relay
Window relay, Decklid (Police
vehicles only)
Power distribution box
The power distribution box is located in the engine compartment. The
power distribution box contains high-current fuses that protect your
vehicle’s main electrical systems from overloads.
WARNING:
Always disconnect the battery before servicing high
current fuses.
WARNING:
To reduce risk of electrical shock, always replace
the cover to the Power Distribution Box before reconnecting the
battery or refilling fluid reservoirs.
If the battery has been disconnected and reconnected, refer to the
Battery
section of the
Maintenance and Specifications
chapter.
2009 Crown Victoria
(cro)
Owners Guide, 1st Printing
USA
(fus)
Roadside Emergencies
187
The high-current fuses are coded as follows.
Fuse/Relay
Location
Fuse Amp
Rating
Protected Circuits
1
30A*
Ignition switch
2
20A*
Spot lights (Police vehicles only)
3
10A*
Powertrain Control Module (PCM)
keep alive power, Canister vent
4
20A*
Fuel relay feed
5
10A*
Rear Air Suspension Module
(RASM)
6
15A*
Alternator regulator
7
30A*
PCM relay feed
8
20A*
Driver’s Door Module (DDM)
9
15A*
Ignition coil relay feed
10
20A*
Horn relay feed
11
15A*
A/C clutch relay feed
2009 Crown Victoria
(cro)
Owners Guide, 1st Printing
USA
(fus)
Roadside Emergencies
188
Fuse/Relay
Location
Fuse Amp
Rating
Protected Circuits
12
20A*
Audio (Subwoofer)
25A*
Police tray lamps (Police vehicles
only)
13
20A*
Instrument panel power point
14
20A*
Stop lamp switch
15
15A*
Police accessory battery feed 1
(Police vehicles only)
16
20A*
Police accessory battery feed 2
(Police vehicles only)
17
10A*
Commercial R/A
18
10A*
Commercial R/A
19
15A*
Injectors
20
15A*
PCM
21
15A*
Powertrain loads and sensors
22
20A*
Police PDB outputs (Police
vehicles only)
23
20A*
Police PDB outputs (Police
vehicles only)
24
10A*
Heated mirrors, Rear defrost
indicator
101
40A**
Blower relay feed
102
50A**
Cooling fan
103
50A**
Instrument panel (I/P) fuse box
feed #1, I/P fuses 10, 12, 14, 16
and 18
104
50A**
Instrument panel (I/P) fuse box
feed #2, I/P fuses 2, 4, 6, 8, 19,
21, 23 and 25
105
30A**
Starter relay feed
106
40A**
Anti-lock Brake System (ABS)
module (Pump)
107
40A**
Rear defroster relay feed
2009 Crown Victoria
(cro)
Owners Guide, 1st Printing
USA
(fus)
Roadside Emergencies
189
Fuse/Relay
Location
Fuse Amp
Rating
Protected Circuits
108
20A**
Police accessory battery feed 3
(Police vehicles only), Cigar
lighter (Non-police vehicles only)
109
20A**
ABS module (Valves)
110
30A**
Wiper module
111
50A**
Police PDB or Police accessory
battery feed (Police vehicles only)
112
30A**
Air suspension compressor
(non-Police vehicles only)
40A**
Police PDB relay feed (Police
vehicles only)
113
50A**
Police light bar or Police
right-hand kick panel accessory
battery feed (Police vehicles only)
114
50A**
Police PDB or Police accessory
battery feed (Police vehicles only)
115
50A**
Rear power point or Police
right-hand kick panel accessory
battery feed (Police vehicles only)
116
50A**
Police accessory battery feed
(Police vehicles only)
117
50A**
Police PDB or Police accessory
battery feed (Police vehicles only)
118
50A**
Rear power point or Police
right-hand kick panel accessory
battery feed (Police vehicles only)
201
1
±
2
ISO relay
A/C clutch
202
Not used
203
1
±
2
ISO relay
Ignition coil
204
1
±
2
ISO relay
PCM
205
Not used
206
1
±
2
ISO relay
Fuel
2009 Crown Victoria
(cro)
Owners Guide, 1st Printing
USA
(fus)
Roadside Emergencies
190
Fuse/Relay
Location
Fuse Amp
Rating
Protected Circuits
207
Not used
208
Not used
209
1
±
2
ISO relay
Horn
301
Full ISO relay
Starter
302
Full ISO relay
Air compressor (non-Police
vehicles only)
RUN/ACC relay (Police vehicles
only)
303
Full ISO relay
Blower
304
Full ISO relay
Rear defrost relay
501
Not used
502
Diode
PCM
503
Not used
601
20A Circuit
breaker
Power seats, Lumbar, Decklid
(Police vehicles only)
602
20A Circuit
breaker
RUN/ACC relay (windows)
(non-Police vehicles only)
RUN/ACC relay feed (windows
and decklid) (Police vehicles
only)
* Mini fuse ** Cartridge fuse
Relays
Relays are located in the power distribution box and should be replaced
by an authorized dealer.
CHANGING A FLAT TIRE
If you get a flat tire while driving:
do not brake heavily.
gradually decrease the vehicle’s speed.
hold the steering wheel firmly.
slowly move to a safe place on the side of the road.
Your vehicle may be equipped with a conventional spare tire that is
different in one or more of the following: type, brand, size, speed rating
2009 Crown Victoria
(cro)
Owners Guide, 1st Printing
USA
(fus)
Roadside Emergencies
191