Honda Civic GX - 2007 Fuse Box Diagram

Honda Civic GX - 2007 Fuse Box Diagram

If equipped
Turn the ignition switch to the ON
(II) position before operating the
moonroof switch on the ceiling
console.
To open the moonroof fully, pull
back the moonroof switch firmly.
The moonroof opens all the way. To
stop the moonroof from opening
fully, briefly move the switch in
either direction.
To tilt the moonroof, push the center
of the moonroof switch straight up.
To stop the moonroof from tilting
fully open, push the moonroof switch
forward.
To open or close the moonroof
partially, pull or push the moonroof
switch lightly to the first detent, and
hold it. The moonroof will stop when
you release the switch.
If your vehicle’s battery is
disconnected or goes dead, or the
driver’s window fuse is removed, the
AUTO function will be disabled. To
reset the AUTO function after
reconnecting the battery or installing
the fuse, do this:
Start the engine. Push down and
hold the driver’s window switch
until the window is fully open.
Pull and hold the driver’s window
switch to close the window
completely, then hold the switch
for about 2 seconds.
If the power windows do not operate
properly after resetting, have your
vehicle checked by your dealer.
1.
2.
CONTINUED
Moonroof
Power Windows, Moonroof
Instruments and Controls
97
MOONROOF SWITCH
Tilt
Close
Open
Your vehicle’s audio system will
disable itself if it is disconnected
from electrical power for any reason.
To make it work again, you must
enter a specific digit code using the
preset buttons (icon on vehicle’s with
navigation system). Because there
are hundreds of number
combinations possible from specific
digits, making the system work
without knowing the exact code is
nearly impossible.
If your vehicle’s battery is
disconnected or goes dead, or the
radio fuse is removed, the audio
system will disable itself. If this
happens, you will see ‘‘ENTER
CODE’’ in the frequency display the
next time you turn on the system.
Use the preset buttons (icons on
vehicles with navigation system) to
enter the code. The code is on the
radio code card included in your
owner’s manual kit. When it is
entered correctly, the radio will start
playing.
If you make a mistake entering the
code, do not start over; complete the
sequence, then enter the correct
code. You have 10 tries to enter the
correct code. If you are unsuccessful
in 10 attempts, you must then leave
the system on for 1 hour before
trying again.
If you lose the card, you must obtain
the code number from a dealer. To
do this, you will need the system’s
serial number.
You should have received a card that
lists your audio system’s code and
serial numbers. It is best to store this
card in a safe place at home. In
addition, you should write the audio
system’s serial number in this owner’s
manual.
On all models except U.S. DX
Radio Theft Protection
168
Diagnosing why the engine won’t
start falls into two areas, depending
on what you hear when you turn the
ignition switch to the START (III)
position:
When you turn the ignition switch to
the START (III) position, you do not
hear the normal noise of the engine
trying to start. You may hear a
clicking sound, a series of clicks, or
nothing at all.
Turn the ignition switch to the
START (III) position. If the
headlights do not dim, check the
condition of the fuses. If the fuses
are OK, there is probably
something wrong with the
electrical circuit for the ignition
switch or starter motor. You will
need a qualified technician to
determine the problem. See
on page
.
If the headlights dim noticeably or
go out when you try to start the
engine, either the battery is
discharged or the connections are
corroded. Check the condition of
the battery and terminal connec-
tions (see page
). You can
then try jump starting the vehicle
from a booster battery (see page
).
You can hear the starter motor
operating normally, or the starter
motor sounds like it is spinning
faster than normal, but the engine
does not start up and run.
You hear nothing, or almost
nothing. The engine’s starter
motor does not operate at all, or
operates very slowly.
Turn the ignition switch to the ON
(II) position. Turn on the
headlights, and check their
brightness. If the headlights are
very dim or do not come on at all,
the battery is discharged. See
on page
.
Check the transmission interlock.
If you have a manual transmission,
the clutch pedal must be pushed
all the way to the floor or the
starter will not operate. With an
automatic transmission, it must be
in Park or neutral.
Check these things:
263
276
252
263
Nothing Happens or the Starter
Motor Operates Very Slowly
Emergency Towing
Jump Starting
If the Engine Won’t Start
Taking Care of the Unexpected
261
In this case, the starter motor’s
speed sounds normal, or even faster
than normal, when you turn the
ignition switch to the START (III)
position, but the engine does not run.
Are you using a properly coded
key? An improperly coded key will
cause the immobilizer system
indicator in the instrument panel
to blink rapidly (see page
).
Are you using the proper starting
procedure? Refer to
on page
.
Do you have fuel? Check the fuel
gauge; the low fuel indicator may
not be working.
There may be an electrical
problem, such as no power to the
fuel pump. Check all the fuses
(see page
).
If you find nothing wrong, you will
need a qualified technician to find
the problem. See
on page
.
77
190
270
276
The Starter Operates Normally
Starting the
Engine
Emergency
Towing
If the Engine Won’t Start
262
The under-hood fuse box is on the
driver’s side, next to the brake fluid
reservoir. To open it, push the tabs
as shown.
If something electrical in your
vehicle stops working, the first thing
you should check for is a blown fuse.
Determine from the chart on pages
and
, or the diagram on the
fuse box lid, which fuse or fuses
control that device. Check those
fuses first, but check all the fuses
before deciding that a blown fuse is
the cause. Replace any blown fuses,
and check if the device works.
The fuses are in two fuse boxes. The
interior fuse box is underneath the
steering column.
274
275
Fuses
Checking and Replacing Fuses
270
INTERIOR
UNDER-HOOD
TAB
FUSE LABEL
Turn the ignition switch to the
LOCK (0) position. Make sure the
headlights and all other
accessories are off.
Remove the cover from the fuse
box.
Check the smaller fuses in the
under-hood fuse box and all the
fuses in the interior fuse box by
pulling out each one with the fuse
puller provided on the back of the
under-hood fuse box cover.
Check each of the large fuses in
the under-hood fuse box by
looking through the top at the wire
inside. Removing these fuses
requires a Phillips-head screw-
driver.
1.
2.
3.
4.
CONTINUED
Fuses
Taking Care of the Unexpected
271
FUSE PULLER
BLOWN
FUSE
BLOWN
If you cannot drive the vehicle
without fixing the problem, and you
do not have a spare fuse, take a fuse
of the same rating or a lower rating
from one of the other circuits. Make
sure you can do without that circuit
temporarily (such as the accessory
power socket or radio).
If you replace the blown fuse with a
spare fuse that has a lower rating, it
might blow out again. This does not
indicate anything wrong. Replace the
fuse with one of the correct rating as
soon as you can.
Look for a blown wire inside the
fuse. If it is blown, replace it with
one of the spare fuses of the same
rating or lower.
If the replacement fuse of the
same rating blows in a short time,
there is probably a serious
electrical problem with your
vehicle. Leave the blown fuse in
that circuit, and have your vehicle
checked by a qualified technician.
6.
5.
Fuses
272
BLOWN
Replacing a fuse with one that has a
higher rating greatly increases the
chances of damaging the electrical
system. If you do not have a
replacement fuse with the proper rating
for the circuit, install one with a lower
rating.
If the driver’s power window fuse is
removed, the AUTO function of the
driver’s window will be disabled. You
should reset the AUTO feature, (see
page
).
If the radio fuse is removed, the
audio system will disable itself. The
next time you turn on the radio you
will see ‘‘ENTER CODE’’ in the
frequency display. Use the preset
buttons to enter the digit code (see
page
).
When the audio system is disabled,
the clock setting in the audio system
will be canceled. You will need to
reset the clock (see page
).
96
168
169
All models except DX
Fuses
Taking Care of the Unexpected
273
ˎ
ˎ
ˎ
ʵ
ʵ
ʵ
ʵ
No.
No.
Circuits Protected
Amps.
Circuits Protected
Amps.
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
1
2
3
Main Fuse
EPS
Option Main
Ignition Switch Main
ABS/VSA Motor
ABS/VSA F/S
50 A
40 A
20 A
20 A
30 A
30 A
40 A
10 A
15 A
15 A
7.5 A
15 A
15 A
15 A
7.5 A
15 A
7.5 A
10 A
Headlight Main
Power Window Main
Not Used
Sub Fan Motor
Main Fan Motor (M/T)
Main Fan Motor (A/T)
Rear Defogger
Blower
Hazard
FI Sub
Stop and Horn
Not Used
Not Used
IGPS Oil Level
Not Used
Audio Amp
IG Coil
FI Main
MG Clutch
DBW
Interior Light
Back Up
100 A
70 A
80 A
50 A
30 A
30 A
40 A
:
U.S. Si model
Fuse Locations
274
UNDER-HOOD FUSE BOX
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ˎ
ˎ
ˎ
ˎ
ˎ
ˎ
No.
No.
No.
Amps.
Circuits Protected
Amps.
Circuits Protected
Amps.
Circuits Protected
:
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
7.5 A
7.5 A
10 A
10 A
10 A
7.5 A
7.5 A
10 A
ODS
METER
SRS
Right Headlight High
Left Headlight High
Small (Interior)
Small (Exterior)
Right Headlight Low
7.5 A
15 A
10 A
7.5 A
(15 A)
Left Headlight Low
Headlight High Main
Small (Main)
Not Used
Headlight Low Main
(HAC)
STS
Moonroof
Door Lock
Driver’s Power Window
Not Used
Rear ACC Socket
ACC
Passenger’s Power Window
Not Used
Right Rear Power Window
Left Rear Power Window
Not Used
ACC Radio
HAC
Daytime Running Light
Wiper
10 A
20 A
15 A
20 A
(7.5 A)
(7.5 A)
(20 A)
20 A
20 A
(15 A)
15 A
20 A
20 A
20 A
7.5 A
10 A
7.5 A
30 A
Power Window
Fuel Pump
Alternator
ABS/VSA
Heated Seat
Not Used
Not Used
Not Used
If equipped
Fuse Locations
Taking Care of the Unexpected
275
INTERIOR FUSE BOX
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ˎ
ˎ
ˎ
ˎ
ˎ
ˎ
ʵ
ʵ
ʵ
ʵ
ʵ
ˎ
ˎ
ˎ
ˎ
ˎ
ˎ
ˎ
ˎ
ˎ
ˎ
Specifications
Technical Information
283
Air Conditioning
Fuses
Alignment
Lights
Battery
Tires
HFC-134a (R-134a)
14.1
15.9 oz (400
450 g)
SP-10
12 V
60 W (HB3)
7°24’
1°30’
0.00 in (0.0 mm)
P195/65R15 89H
0.08 in (2.0 mm)
Refrigerant type
Charge quantity
Lubricant oil type
Interior
Under-hood
Toe-in
Camber
Caster
12 V
12 V
12 V
12 V
12 V
12 V
12 V
12 V
8 W
5 W
21 W
3 CP
21 W
21/5 W
21 W
21/5 W
12 V
51 W (HB4)
12 V
2 CP
12 V
8 W
12 V
5 W
P205/55R16 89H
Headlights
Front turn signal/side marker/
Parking lights
Rear turn signal lights
Stop/Taillights
Rear side marker lights
Back-up lights
Taillights
High-mount brake light
License plate lights
Ceiling light
Spotlights
Trunk light
Capacity
60 psi (420 kPa , 4.2 kgf/cm
)
30 psi (210 kPa , 2.1 kgf/cm
)
32 psi (220 kPa , 2.2 kgf/cm
)
T125/70D15 95M
12 V
12 V
12 V
12 V
36 AH/5 HR
45 AH/20 HR
38 AH/5 HR
45 AH/20 HR
Size
Pressure
12 V
47 AH/20 HR
P215/45R17 87V
215/45R17 91W
T125/70D16 96M
32 psi (220 kPa , 2.2 kgf/cm
)
29 psi (200 kPa , 2.0 kgf/cm
)
See page
275
or the fuse label
attached to the inside of the fuse
box door under the steering
column.
See page
274
or the fuse box
cover.
High
Low
Front
Rear
Front
Rear
Front
1 :
2 :
3 :
LX, EX
DX, Canadian DX-G
U.S. Si (all season tires)
4 :
5 :
6 :
Except U.S. Si
Optional for U.S. Si (summer tires)
U.S. Si
U.S.
Vehicles
Canada
Vehicles
Front/Rear
Spare
Front/Rear
Front
Rear
Spare
3
3
3
1
2
4
6
1
2
5
ʵ
When you push the MAIN switch in,
the switch is OFF, and the
passenger’s window cannot be raised
or lowered. To cancel this feature,
push on the switch again to get it to
pop out. Keep the MAIN switch off
when you have children in the
vehicle so they do not injure
themselves by operating the window
unintentionally.
If the driver’s
window runs into any obstacle while
it is closing automatically, it will
reverse direction, and then stop. To
close the window, remove the
obstacle, then use the window switch
again.
Auto reverse stops sensing when the
window is almost closed. You should
always check that all passengers and
objects are away from the window
before closing it.
Start the engine. Push down and
hold the driver’s window switch
until the window is fully open.
If the power windows do not operate
properly after resetting, have your
vehicle checked by your dealer.
Pull and hold the driver’s window
switch to close the window
completely, then hold the switch
for about 2 seconds.
If your vehicle’s battery is
disconnected or goes dead, or the
driver’s window fuse is removed, the
AUTO function could be disabled. If
the power window system needs to
be reset after reconnecting the
battery or installing the fuse, do this:
1.
2.
AUTO REVERSE
Power Windows
98
Your vehicle’s audio system will
disable itself if it is disconnected
from electrical power for any reason.
To make it work again, you must
enter a specific digit code using the
preset buttons (icon on vehicle’s with
navigation system). Because there
are hundreds of number
combinations possible from specific
digits, making the system work
without knowing the exact code is
nearly impossible.
If your vehicle’s battery is
disconnected or goes dead, or the
radio fuse is removed, the audio
system will disable itself. If this
happens, you will see ‘‘ENTER
CODE’’ in the frequency display the
next time you turn on the system.
Use the preset buttons (icons on
vehicles with navigation system) to
enter the code. The code is on the
radio code card included in your
owner’s manual kit. When it is
entered correctly, the radio will start
playing.
If you make a mistake entering the
code, do not start over; complete the
sequence, then enter the correct
code. You have 10 tries to enter the
correct code. If you are unsuccessful
in 10 attempts, you must then leave
the system on for 1 hour before
trying again.
If you lose the card, you must obtain
the code number from a dealer. To
do this, you will need the system’s
serial number.
You should have received a card that
lists your audio system’s code and
serial numbers. It is best to store this
card in a safe place at home. In
addition, you should write the audio
system’s serial number in this owner’s
manual.
U.S. LX, EX, Si and all Canadian models
Radio Theft Protection
172
Do you have fuel? Check the fuel
gauge; the low fuel indicator may
not be working.
There may be an electrical
problem, such as no power to the
fuel pump. Check all the fuses
(see page
).
If you find nothing wrong, you will
need a qualified technician to find
the problem. See
on page
.
Are you using a properly coded
key? An improperly coded key will
cause the immobilizer system
indicator in the instrument panel
to blink rapidly (see page
).
Are you using the proper starting
procedure? Refer to
on page
.
In this case, the starter motor’s
speed sounds normal, or even faster
than normal, when you turn the
ignition switch to the START (III)
position, but the engine does not run.
Turn the ignition switch to the
START (III) position. If the
headlights do not dim, check the
condition of the fuses. If the fuses
are OK, there is probably
something wrong with the
electrical circuit for the ignition
switch or starter motor. You will
need a qualified technician to
determine the problem. See
on page
.
If the headlights dim noticeably or
go out when you try to start the
engine, either the battery is
discharged or the connections are
corroded. Check the condition of
the battery and terminal connec-
tions (see page
). You can
then try jump starting the vehicle
from a booster battery (see page
).
194
274
250
261
76
268
274
Emergency
Towing
The Starter Operates Normally
Starting the
Engine
Emergency Towing
If the Engine Won’t Start
260
The vehicle’s fuses are contained in
two fuse boxes.
If something electrical in your
vehicle stops working, check for a
blown fuse first. Determine from the
chart on pages
and
, or the
diagram on the fuse box lid, which
fuse or fuses control that device.
Check those fuses first, but check all
the fuses before deciding that a
blown fuse is the cause. Replace any
blown fuses, and check if the device
works.
The interior fuse box is on the
driver’s lower left side.
The under-hood fuse box is in the
engine compartment on the driver’s
side, next to the brake fluid reservoir.
To open it, push the tabs as shown.
272
273
Fuses
Checking and Replacing Fuses
268
UNDER-HOOD
INTERIOR
TAB
CONTINUED
Check each of the large fuses in
the under-hood fuse box by
looking through the top at the wire
inside. Removing these fuses
requires a Phillips-head screw-
driver.
Turn the ignition switch to the
LOCK (0) position. Make sure the
headlights and all other
accessories are off.
Remove the cover from the fuse
box.
Check the smaller fuses in the
under-hood fuse box and all the
fuses in the interior fuse box by
pulling out each one with the fuse
puller provided on the back of the
under-hood fuse box cover.
4.
3.
1.
2.
Fuses
Taking Care of the Unexpected
269
FUSE
BLOWN
FUSE PULLER
FUSE
BLOWN
If the replacement fuse of the
same rating blows in a short time,
there is probably a serious
electrical problem in your vehicle.
Leave the blown fuse in that
circuit and have your vehicle
checked by a qualified technician.
Look for a blown wire inside the
fuse. If it is blown, replace it with
one of the spare fuses of the same
rating or lower.
If you cannot drive the vehicle
without fixing the problem, and you
do not have a spare fuse, take a fuse
of the same rating or a lower rating
from one of the other circuits. Make
sure you can do without that circuit
temporarily (such as the accessory
power socket or radio).
If you replace the blown fuse with a
spare fuse that has a lower rating, it
might blow out again. This does not
indicate anything wrong. Replace the
fuse with one of the correct rating as
soon as you can.
6.
5.
Fuses
270
BLOWN
Replacing a fuse with one that has a
higher rating greatly increases the
chances of damaging the electrical
system. If you do not have a
replacement fuse with the proper rating
for the circuit, install one with a lower
rating.
Your vehicle has spare fuses on
the back of the under-hood fuse
box cover.
If the radio fuse is removed, the
audio system will disable itself. The
next time you turn on the radio you
will see ‘‘ENTER CODE’’ in the
frequency display. Use the preset
buttons to enter the digit code (see
page
).
If the driver’s power window fuse is
removed, the AUTO function of the
driver’s window will be disabled. You
should reset the AUTO feature, (see
page
).
When the audio system is disabled,
the clock setting in the audio system
will be canceled. You will need to
reset the clock (see page
).
3.
97
172
173
All models except DX
Fuses
Taking Care of the Unexpected
271
FUSE PULLER
SPARE FUSES
ˎ
ˎ
ˎ
ʵ
ʵ
ʵ
ʵ
Amps.
No.
Circuits Protected
Circuits Protected
Amps.
No.
100 A
70 A
80 A
50 A
30 A
30 A
40 A
50 A
40 A
1
2
3
4
Main Fuse
EPS
Option
Ignition Switch Main
ABS/VSA Motor
ABS/VSA F/S
Headlight Main
Power Window Main
Not Used
Fan Motor
Main Fan Motor (A/T)
Main Fan Motor (M/T)
Rear Defroster
Blower
Hazard
FI
Stop, Horn
Not Used
Not Used
Oil Level Sensor
Not Used
Audio Amp
Ignition Coil
FI Main
MG Clutch
DBW
Interior Light
Back Up
20 A
30 A
20 A
40 A
40 A
10 A
15 A
15 A
7.5 A
15 A
15 A
15 A
7.5 A
15 A
7.5 A
10 A
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
: Si model
Fuse Locations
272
UNDER-HOOD FUSE BOX
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ˎ
ˎ
ˎ
ˎ
ˎ
No.
Amps.
No.
Amps.
Circuits Protected
Amps.
No.
Circuits Protected
Circuits Protected
1
2
3
4
5
6
7
8
7.5 A
15 A
10 A
7.5 A
15 A
20 A
9
10
11
12
13
14
15
16
7.5 A
7.5 A
10 A
10 A
10 A
7.5 A
7.5 A
10 A
ODS (Occupant Detection
System)
Meter
SRS
Right Headlight High Beam
Left Headlight High Beam
Small Lights (Interior)
Small Lights (Exterior)
Right Headlight Low Beam
10 A
20 A
15 A
20 A
20 A
20 A
20 A
20 A
15 A
15 A
20 A
7.5 A
10 A
7.5 A
30 A
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
Left Headlight Low Beam
Headlight High Beam Main
Small Lights Main
Not Used
Headlight Low Beam Main
Not Used
Not Used
Moonroof
Door Lock
Driver’s Power Window
HAC Option
Rear Accessory Socket
Accessory
Front Passenger’s Power
Window
Not Used
Not Used
Not Used
Not Used
Accessory, Radio
IG2 HAC
Daytime Running Lights
Front Wiper
Power Window
Fuel Pump
IG1 ACG
ABS/VSA
Audio Amp
Front Fog Lights
Not Used
Not Used
: On models equipped
Fuse Locations
Taking Care of the Unexpected
273
INTERIOR FUSE BOX
ʵ
ʵ
ʵ
ˎ
ˎ
ˎ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ˎ
ˎ
ˎ
ˎ
ˎ
ˎ
ˎ
ˎ
ˎ
ˎ
ˎ
ˎ
ˎ
ˎ
ˎ
ˎ
ˎ
ˎ
Specifications
Technical Information
281
Air Conditioning
Lights
Battery
Fuses
Alignment
Tires
HFC-134a (R-134a)
14.1
15.9 oz (400
450 g)
12 V
12 V
60 W
12 V
51 W
Refrigerant type
Charge quantity
Lubricant oil type
28/8 W
SP-10
12 V
12 V
12 V
12 V
21/5 W
12 V
21 W
12 V
12 V
12 V
5 W
8 W
3 CP
21 W
18 W
Headlights (HI)
Headlights (LO)
Front turn signal/Side marker/
Parking light
Rear turn signal lights
Stop/Taillights
Rear side marker lights
Back-up lights
High-mount brake light
License plate lights
Ceiling light
Spotlights
Trunk light
Capacity
36 AH/5 HR
Interior
Under-hood
Toe-in
Camber
Caster
0.00 in (0.0 mm)
0.08 in (2.0 mm)
1°30’
P195/65R15 89H
12 V
3 CP
12 V
P205/55R16 89H
P215/45R17 87V
12 V
12 V
47 AH/20 HR
45 AH/20 HR
T135/80R16 101M
T125/70D15 95M
Size
Pressure
12 V
38 AH/5 HR
215/45ZR17 91W
8 W
See page
273
or the fuse label
attached to the dashboard.
See page
272
or the fuse box
cover.
32 psi (220 kPa , 2.2 kgf/cm
)
60 psi (420 kPa , 4.2 kgf/cm
)
Front
Rear
Front
Rear
Front
(HB3)
(HB4)
1 : U.S.: DX, LX, EX
2 : Canada: DX, DX-G,LX, EX
3 : Si
1 :
2 :
3 :
4 :
5 :
6 :
U.S. DX, Canada DX, DX-G
LX,EX
Si (all season tires)
U.S.: DX, LX, EX, Canada: DX, DX-G, LX, EX
Optional for Si (summer tires)
Si
: All models except EX and Si
Front/Rear
Spare
Front/Rear
Spare
1
2
1
3
1
2
3
5
4
6