Honda Odyssey - 2006 Fuse Box Diagram

Honda Odyssey - 2006 Fuse Box Diagram

The power tailgate has an auto-
reverse feature. If it meets
resistance while opening or closing,
it will beep three times and reverse
direction. However, the tailgate may
not reverse immediately. Always
make sure passengers and objects
are clear of the tailgate before
opening or closing it.
Also check that passengers,
especially children, do not have their
hands on the edge of the tailgate or
on the tailgate sill. The auto reverse
feature stops working when the
tailgate is about to latch so the motor
can pull the tailgate shut.
If your vehicle’s battery is
disconnected, goes dead, or the fuse
is removed while the tailgate is fully
open, the power tailgate needs to be
reset. After connecting the battery
or installing the fuse, close the
tailgate fully by hand.
The power tailgate may not open or
close under the these conditions:
When the tailgate or the roof is
covered with snow or ice.
Do not install any accessories on the
tailgate. It may cause the tailgate not
to function properly. If there is snow
or ice on the tailgate, make sure to
remove it before you operate the
tailgate.
If you pull the tailgate release handle
while the tailgate is opening or
closing, it will stop moving. You need
to open or close it the rest of the way
manually.
The tailgate has sensors on both
sides. Be careful not to damage them.
If the sensors are damaged, the
power tailgate does not function
properly.
When the vehicle is swayed in a
strong wind.
The vehicle is parked on a steep
hill.
Auto-Reverse
Tailgate
144
Closing a power tailgate while
anyone is in the path of the
tailgate can cause serious
injury.
Make sure everyone is clear
before closing the power
tailgate.
Start the engine. Push down and
hold the driver’s window switch
until the window is fully open.
Pull and hold the driver’s window
switch to close the window
completely, then hold the switch
for about 2 seconds.
Press the UNLOCK button a
second time, and hold it. The
passenger’s doors unlock, and all
four windows start to open. To
stop the windows, release the
button.
To open the windows further,
press the button again and hold it.
If the windows stop before the
desired position, repeat steps 1
and 2.
You cannot close the windows with
the remote transmitter.
If the power windows do not operate
properly after resetting, have your
vehicle checked by your dealer.
Press the UNLOCK button once
to unlock the driver’s door.
You can open all of the windows
from the outside with the remote
transmitter.
If your vehicle’s battery is
disconnected or goes dead, or the
driver’s window fuse is removed, the
AUTO function will be disabled. The
power window system needs to be
reset after reconnecting the battery
or installing the fuse.
1.
2.
3.
1.
2.
On EX, EX-L and Touring models
Opening the Windows with the
Remote Transmitter
Power Windows
168
ʵ
ʵ
ʵ
The preset frequencies will be lost if
your vehicle’s battery goes dead, is
disconnected, or the radio fuse is
removed.
Press the A. SEL button. ‘‘A.SEL’’
flashes in the display, and the system
goes into scan mode for several
seconds. It stores the frequencies of
six AM and twelve FM stations in
the preset buttons.
To turn off auto select, press the
A. SEL button. This restores the
presets you originally set.
You will see a ‘‘0’’ displayed after
pressing a preset button if auto
select cannot find a strong station for
every preset button.
If you do not like the stations auto
select has stored, you can store
other frequencies on the preset
buttons. Use the TUNE, SEEK, or
SCAN functions to find stations, then
store them in the preset buttons as
described.
If you are
traveling far from home and can no
longer receive your preset stations,
you can use the auto select feature to
find stations in the local area.
Press the SOUND (TUNE) knob
repeatedly to display the bass, treble,
balance, and fader settings.
Each mode is shown in the display as
it changes. Turn the SOUND
(TUNE) knob to adjust the setting to
your liking. When the level reaches
the center, you will see ‘‘CENTER’’
in the display. The system will
automatically return the display to
the selected audio mode about 5
seconds after you stop adjusting a
mode.
Use the TRE/BAS
modes to adjust the tone to your
liking.
These two
modes adjust the strength of the
sound coming from each speaker.
BAL adjusts the side-to-side strength,
while FAD adjusts the front-to-back
strength.
Adjusting the Sound
AUTO SELECT
Treble/Bass
Balance/Fader
Playing the AM/FM Radio
206
ʵ
ʵ
ʵ
ʴ
ʵ
ʵ
On models with a rear entertainment
system and a navigation system, you
cannot listen to XM Radio and a disc
at the same time. For example, when
XM Radio is playing on the front
speakers, you cannot listen to a disc
on the rear speakers, or vice versa.
The scan function gives
you a sampling of all channels while
in the channel mode. In the category
mode, only the channels within that
category are scanned. To activate
scan, press the SCAN/RPT button or
touch the SCAN icon on the audio
display. The system plays each
channel in numerical order for a few
seconds, then selects the next
channel. When you hear a channel
you want to continue listening to,
press the button or touch the icon
again.
Press either side of
the bar (
or
) to select another
category.
In the category mode, only channels
within that category can be selected.
In the channel mode, all channels
can be selected.
Use the TUNE knob, or the
CATEGORY or SCAN buttons to
tune to a desired channel. You can
also touch the SCAN icon on the
audio display.
Press the XM RADIO button.
Either XM1 or XM2 will show in
the display.
To store a channel:
You can store up to 12
preset channels using the six preset
buttons or preset icons on the audio
display. Each button stores one
channel from the XM1 band and one
channel from the XM2 band.
The presets will be lost if your
vehicle’s battery goes dead, is
disconnected, or the radio fuse is
removed.
Once a channel is stored, press and
release the proper preset button
(icon) to tune to it.
Press the XM RADIO button again
or touch the other XM icon (XM1
or XM2) on the audio display.
Store the next six channels using
steps 2 and 3.
Repeat steps 2 and 3 to store the
first six channels.
Pick the preset button (icon) you
want for that channel. Press and
hold the button (icon) until you
hear a beep.
Turn the tune knob left or
right to select channels. In the
category mode, you can only select
channels within that category.
1.
2.
3.
4.
5.
Playing the XM
Satellite Radio
SCAN
CATEGORY
Preset
TUNE
Features
213
Your vehicle’s audio system will
disable itself if it is disconnected
from electrical power for any reason.
To make it work again, you must
enter a specific five-digit code with
the preset buttons. Because there
are hundreds of number
combinations possible from the five
digits, making the system work
without knowing the exact code is
nearly impossible.
You should have received a card that
lists your audio system code number
and serial number. It is best to store
this card in a safe place at home. In
addition, you should write the audio
system’s serial number in this
Owner’s Manual.
If you should happen to lose the card,
you must obtain the code number
from a Honda dealer. To do this, you
will need the system’s serial number.
If your vehicle’s battery is discon-
nected or goes dead, or the radio
fuse is removed, the audio system
will disable itself. If this happens,
you will see ‘‘
’’ in the
frequency display the next time you
turn on the system. Use the preset
buttons to enter the five-digit code.
The code is located on the radio code
card included in your Owner’s
Manual kit. When it is entered
correctly, the radio will start playing.
If you make a mistake entering the
code, do not start over; complete the
five-digit sequence, then enter the
correct code. You have 10 tries to
enter the correct code. If you are
unsuccessful in 10 attempts, you
must then leave the system on for 1
hour before trying again.
You will have to store your favorite
stations in the preset buttons after
the system begins working. Your
original settings were lost when the
power was disconnected.
On EX, EX-L and Touring models
Radio Theft Protection
234
Diagnosing why the engine won’t
start falls into two areas, depending
on what you hear when you turn the
ignition switch to the START (III)
position:
Check the transmission interlock.
The transmission must be in Park
or neutral or the starter will not
operate.
Turn the ignition switch to the ON
(II) position. Turn on the
headlights, and check their
brightness. If the headlights are
very dim or do not come on at all,
the battery is discharged. See
on page
.
If the headlights dim noticeably or
go out when you try to start the
engine, either the battery is
discharged or the connections are
corroded. Check the condition of the
battery and terminal connections
(see page
). You can then try
jump starting the vehicle from a
booster battery (see page
).
In this case, the starter motor’s
speed sounds normal, or even faster
than normal, when you turn the
ignition switch to the START (III)
position, but the engine does not run.
Are you using the proper starting
procedure? Refer to
on page
.
Turn the ignition switch to the
START (III) position. If the
headlights do not dim, check the
condition of the fuses. If the fuses
are OK, there is probably
something wrong with the
electrical circuit for the ignition
switch or starter motor. You will
need a qualified technician to
determine the problem (see
on page
).
Check these things:
When you turn the ignition switch to
the START (III) position, you do not
hear the normal noise of the engine
trying to start. You may hear a
clicking sound or series of clicks, or
nothing at all.
You can hear the starter motor
operating normally, or the starter
motor sounds like it is spinning
faster than normal, but the engine
does not start up and run.
You hear nothing, or almost
nothing. The engine’s starter
motor does not operate at all, or
operates very slowly.
373
387
373
299
359
Jump Starting
The Starter Operates Normally
Starting the
Engine
Emergency Towing
Nothing Happens or the Starter
Motor Operates Very Slowly
If the Engine Won’t Start
372
Are you using a properly coded
key? An improperly coded key will
cause the immobilizer system
indicator in the instrument panel
to blink rapidly (see page
).
Do you have fuel? Check the fuel
gauge; the low fuel indicator may
not be working.
There may be an electrical
problem, such as no power to the
fuel pump. Check all the fuses
(see page
).
If you find nothing wrong, you will
need a qualified technician to find
the problem. See
on page
.
Although this seems like a simple
procedure, you should take several
precautions.
Open the hood, and check the
physical condition of the battery.
In very cold weather, check the
condition of the electrolyte. If it
seems slushy or frozen, do not try
jump starting until it thaws.
You cannot start your vehicle by
pushing or pulling it.
Turn off all the electrical
accessories: heater, A/C, climate
control, audio system, lights, etc.
Put the transmission in neutral or
Park, and set the parking brake.
1.
2.
133
382
387
CONTINUED
Emergency
Towing
Jump Starting
To Jump Start Your Vehicle:
If the Engine Won’t Start, Jump Starting
Taking Care of the Unexpected
373
A battery can explode if you do
not follow the correct procedure,
seriously injuring anyone
nearby.
Keep all sparks, open flames,
and smoking materials away
from the battery.
If a battery sits in extreme cold, the
electrolyte inside can freeze.
Attempting to jump start with a frozen
battery can cause it to rupture.
If the electric motor will not close
the moonroof, do the following:
Check the fuse for the moonroof
motor (see page
). If the fuse
is blown, replace it with one of the
same or lower rating.
Try closing the moonroof. If the
new fuse blows immediately or the
moonroof motor still does not
operate, you can close the
moonroof manually.
Get the moonroof wrench out of
the tool kit in the cargo area.
Use a screwdriver or coin to
remove the round plug in the
center of the headliner.
Insert the moonroof wrench into
the socket behind this plug. Turn
the wrench until the moonroof is
fully closed.
Remove the wrench. Reinstall the
round plug.
If you need to close the moonroof
manually, it means the moonroof
opening/closing function is
developing a problem. Have your
vehicle checked by your dealer.
4.
6.
5.
1.
2.
3.
385
Closing the Moonroof
380
ROUND PLUG
SOCKET
The vehicle’s fuses are contained in
four fuse boxes (three, if the vehicle
does not have a rear entertainment
system).
To open the passenger’s fuse box,
pull the right edge of the cover.
The interior fuse boxes are located
under the dashboard on the driver’s
and passenger’s side.
The primary under-hood fuse box is
on the passenger’s side. To open it,
push the tabs as shown.
The secondary under-hood fuse box
is behind the primary fuse box.
Fuses
Taking Care of the Unexpected
381
DRIVER’S SIDE INTERIOR
PASSENGER’S SIDE
INTERIOR
PRIMARY UNDER-HOOD FUSE BOX
SECONDARY UNDER-HOOD FUSE BOX
Check the smaller fuses in the
under-hood fuse box and all the
fuses in the interior fuse boxes by
pulling out each fuse with the fuse
puller provided in the primary
under-hood fuse box.
Turn the ignition switch to the
LOCK (0) position. Make sure the
headlights and all other
accessories are off.
Check each of the large fuses in
the primary under-hood fuse box
by looking through the top at the
wire inside. Removing these fuses
requires a Phillips-head
screwdriver.
If something electrical in your
vehicle stops working, the first thing
you should check for is a blown fuse.
Determine from the chart on pages
through
, or the diagram on
the fuse box lid, which fuse or fuses
control that device. The diagram for
the interior driver’s side fuse box is
on the kick panel below the fuse box.
Check those fuses first, but check all
the fuses before deciding that a
blown fuse is the cause. Replace any
blown fuses, and check if the device
works.
Remove the cover from the fuse
box.
1.
2.
3.
4.
384
386
Checking and Replacing Fuses
Fuses
382
FUSE
BLOWN
FUSE PULLER
If the replacement fuse of the
same rating blows in a short time,
there is probably a serious
electrical problem with your
vehicle. Leave the blown fuse in
that circuit, and have your vehicle
checked by a qualified mechanic.
If the radio fuse is removed, the
audio system will disable itself. The
next time you turn on the radio you
will see ‘‘
’’ in the frequency
display. Use the preset buttons to
enter the five-digit code (see page
).
If you cannot drive the vehicle
without fixing the problem, and you
do not have a spare fuse, take a fuse
of the same rating or a lower rating
from one of the other circuits. Make
sure you can do without that circuit
temporarily (such as the accessory
power socket or radio).
If you replace the blown fuse with a
spare fuse that has a lower rating, it
might blow out again. This does not
indicate anything wrong. Replace the
fuse with one of the correct rating as
soon as you can.
Look for a blown wire inside the
fuse. If it is blown, replace the fuse
with one of the spare fuses of the
same rating or lower.
If the driver’s power window fuse is
removed, the AUTO function of the
driver’s window will be disabled. You
should reset the AUTO feature, (see
page
).
5.
6.
168
234
CONTINUED
On EX, EX-L and Touring models
Fuses
Taking Care of the Unexpected
383
BLOWN
Replacing a fuse with one that has a
higher rating greatly increases the
chances of damaging the electrical
system. If you do not have a
replacement fuse with the proper
rating for the circuit, install one with
a lower rating.
ʵ
ʵ
ʴ
ʴ
ʵ
ˎ
ˎ
ˎ
ˎ
ˎ
ˎ
ˎ
ˎ
No.
Amps.
No.
No.
Amps.
Circuits Protected
Amps.
Circuits Protected
No.
Amps.
Circuits Protected
Circuits Protected
1
2
3
4
5
6
7
8
9
10
11
12
10 A
30 A
10 A
15 A
10 A
10 A
7.5 A
15 A
30 A
30 A
7.5 A
If equipped
13
14
15
16
17
18
19
20
21
22
23
If equipped
1
2
3
4
5
6
40 A
40 A
40 A
20 A
20 A
Left Headlight Low
Rear Defroster Coil
Left Headlight High
Small Lights
Right Headlight Low
Right Headlight High
Back Up
FI ECU
Condenser Fan
Not used
Cooling Fan
MG Clutch
20 A
30 A
40 A
15 A
30 A
30 A
30 A
40 A
40 A
70 A
120 A
50 A
40 A
Horn, Stop
Defroster
Back Up
Hazard
VSA Motor
VSA
Option 1
Option 2
Heater Motor
B AS F/B
Battery
B IGI Main
Power Window
7
8
9
10
11
10 A
10 A
7.5 A
7.5 A
Not Used
Left Power Sliding Door
Right Power Sliding Door
Power Tailgate
Premium
AC Inverter
Front Fog Light
ACM
TPMS
Not Used
Rear Entertainment System
:
:
Fuse Locations
384
PRIMARY UNDER-HOOD FUSE BOX
SECONDARY UNDER-HOOD FUSE BOX
ʵ
ʵ
ʵ
ʵ
ˎ
ˎˎ
ˎ
ˎˎ
ˎˎ
ˎˎ
ˎˎ
ˎˎ
No.
Amps.
No.
Circuits Protected
Circuits Protected
Amps.
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
15 A
15 A
10 A
7.5 A
10 A
7.5 A
20 A
20 A
20 A
20 A
20 A
10 A
10 A
7.5 A
If equipped
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
IG ACG
IG Fuel Pump
IG Washer
IG Meter
IG SRS
IGP
Left Rear Window
Right Rear Window
Passenger’s Window
Driver’s Window
Moonroof
Not Used
IG HAC
Not Used
ACC
HAC Option
Not Used
IG Coil
Daytime Running Light
LAF
Radio
Interior Lights
Not Used
Door Lock
Front Accessory Socket
OPDS
IG, Wiper
Rear Accessory Socket
Left Power Sliding Door
Closer
Dr Power Seat Slide
ADJ Pedals
Dr Power Seat Recline
Power Tailgate Closer
15 A
10 A
15 A
7.5 A
7.5 A
20 A
15 A
7.5 A
30 A
15 A
20 A
20 A
20 A
20 A
20 A
:
:
Canadian models
Fuse Locations
Taking Care of the Unexpected
385
INTERIOR FUSE BOX
Driver’s Side
Front
ʵ
ʵ
ˎ
ˎ
No.
Amps.
Circuits Protected
1
2
3
4
5
6
7
8
9
If equipped
30 A
15 A
20 A
15 A
7.5 A
20 A
15 A
Rear Blower
Not Used
DBW
Door Lock
Not Used
Heated Seat
Instrument Panel
Right Power Sliding Door
Front Accessory Sockets
:
Fuse Locations
386
INTERIOR FUSE BOX
Passenger’s Side
ʵ
ˎ
ˎ
ˎ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ˎ
ˎ
ˎ
Specifications
Technical Information
393
Alignment
Tires
Fuses
Battery
Lights
60 W (HB3)
12 V
12 V
21 W
51 W (HB4)
21 W
12 V
12 V
Toe-in
Camber
Caster
0.00 in (0.0 mm)
0.08 in (2.0 mm)
0°30’
2°32’
Size
Pressure
235/65R16 103T
235-710R460A 104T
T135/80D17 103M
33 psi (230 kPa , 2.3 kgf/cm
)
12 V
35 W
60 psi (420 kPa , 4.2 kgf/cm
)
35 psi (240 kPa , 2.4 kgf/cm
)
35 psi (240 kPa , 2.4 kgf/cm
)
12 V
12 V
12 V
12 V
12 V
21 W
21/5 W
21 W
12 V
12 V
12 V
2 W
12 V
12 V
1.5 CP
3 CP
5 W
16 W
5 W
5 W
Interior
Under-hood
Capacity
12 V
12 V
65 AH/20 HR
52 AH/5 HR
12 V
12 V
8 W
4 W (2 CP)
Headlights
Front turn signal
Front fog lights
Front turn signal lights
Front parking/side marker
lights
Rear turn signal lights
Stop/Taillights
Taillights
Back-up lights
License plate light
High-mount brake light
Individual map lights
Vanity mirror lights
Cargo area light
Door courtesy light
See page
385
or the fuse label
attached to the dashboard.
See page
386
or the fuse label
attached to the inside of the fuse
box door under the dashboard.
See page
384
or the fuse box
cover.
Front
Rear
Front
Rear
Front
U.S. Touring model
Front/Rear
Spare
Front
Rear
Spare
(Amber)
(Amber)
Driver’s side
Passenger’s side
1 :
2 :
3 :
LX, EX, and Canadian Touring models
Front
Rear
High
Low
EX-L and Canadian Touring models
1
2
3