Honda CR-V - 2002 Fuse Box Diagram

Honda CR-V - 2002 Fuse Box Diagram

If your vehicle’s battery is
disconnected or goes dead, or the
driver’s window fuse is removed, the
AUTO function will be disabled. The
power window system needs to be
reset after reconnecting the battery
or installing the fuse. You should do
the following.
Start the engine. Push down on
the driver’s window switch until
the window is fully open.
Pull back on the driver’s window
switch to close the window
completely, then hold the switch
for a second or two more.
If the power windows do not operate
properly after resetting, have your
vehicle checked by a Honda dealer.
Auto reverse stops sensing when the
window is almost closed. You should
always check that all passengers and
objects are away from the window
before closing it.
If the driver’s window runs into any
obstacle while it is closing
automatically, it will reverse
direction, and then stop. To close the
window, remove the obstacle, then
use the window switch again.
1.
2.
Power Windows
Instruments and Controls
Auto Reverse
112
ʵ
ʵ
˓
˓
ʵ
ʵ
ʵ
ʴ
To store a frequency:
Select the desired band, AM or
FM. FM1 and FM2 let you store
two frequencies with each Preset
button.
Pick the Preset button you want
for that station. Press the button
and hold it until you hear a beep.
Repeat steps 1 to 3 to store a total
of six stations on AM and twelve
on FM.
Once a station’s frequency is stored,
simply press and release the proper
preset button to tune to it.
You can use any of five methods to
find radio stations on the selected
band: TUNE, SEEK, SCAN, AUTO
SELECT, and the Preset buttons.
Use the TUNE knob to
tune the radio to a desired frequency.
Turn the TUNE knob to the right to
tune to a higher frequency, or to the
left to tune to a lower frequency.
Turn the knob right or left until the
display reaches the desired
frequency.
The SEEK function
searches the band for a station with
a strong signal. To activate it, press
either SEEK button (
or
), then
release it. Depending on which
SEEK button you press, the system
scans upward or downward from the
current frequency. It stops when it
finds a station with a strong signal.
The SCAN function
samples all the stations with strong
signals on the selected band. To
activate it, press the SCAN button,
then release it. You will see SCAN in
the display. The system will scan up
the band for a station with a strong
signal. When it finds one, it will stop
and play that station for
approximately five seconds. If you do
nothing, the system will then scan
for the next strong station and play
that for five seconds. When it plays a
station that you want to continue
listening to, press the SCAN button
again.
You can store the
frequencies of your favorite radio
stations in the six preset buttons.
Each button will store one frequency
on the AM band, and two
frequencies on the FM band.
Use the TUNE, SEEK, or SCAN
function to tune the radio to a
desired station.
The preset frequencies will be lost if
your vehicle’s battery goes dead, is
disconnected, or the radio fuse is
removed.
1.
2.
3.
4.
Audio System
Comfort and Convenience Features
TUNE
SEEK
SCAN
Preset
140
ʵ
ʵ
The SCAN function
samples all the stations with strong
signals on the selected band. To
activate it, press the SCAN button,
then release it. You will see SCAN in
the display. The system will scan up
the band for a station with a strong
signal. When it finds one, it will stop
and play that station for
approximately five seconds. If you do
nothing, the system will then scan
for the next strong station and play
that for five seconds. When it plays a
station that you want to continue
listening to, press the SCAN button
again.
You can store the
frequencies of your favorite radio
stations in the six preset buttons.
Each button will store one frequency
on the AM band, and two
frequencies on the FM band.
To store a frequency:
Once a station’s frequency is stored,
simply press and release the proper
preset button to tune to it.
The preset frequencies will be lost if
your vehicle’s battery goes dead, is
disconnected, or the radio fuse is
removed.
Repeat steps 1 to 3 to store a total
of six stations on AM and twelve
on FM.
Pick the Preset button you want
for that station. Press the button
and hold it until you hear a beep.
Use the TUNE, SEEK, or SCAN
function to tune the radio to a
desired station.
Select the desired band, AM or
FM. FM1 and FM2 let you store
two frequencies with each Preset
button.
1.
2.
3.
4.
SCAN
Preset
Audio System
Comfort and Convenience Features
156
You will have to store your favorite
stations in the Preset buttons after
the system begins working. Your
original settings were lost when
power was disconnected.
If your vehicle’s battery is discon-
nected or goes dead, or the radio
fuse is removed, the audio system
will disable itself. If this happens,
you will see ‘‘
’’ in the
frequency display the next time you
turn on the system. Use the Preset
buttons to enter the five-digit code. If
it is entered correctly, the radio will
start playing.
If you make a mistake entering the
code, do not start over or try to
correct your mistake. Complete the
five-digit sequence, then enter the
correct code. You have ten tries to
enter the correct code. If you are
unsuccessful in ten attempts, you
must then leave the system on for
one hour before trying again.
Your vehicle’s audio system will
disable itself if it is disconnected
from electrical power for any reason.
To make it work again, the user
must enter a specific five-digit code
in the Preset buttons. Because there
are hundreds of number
combinations possible from five
digits, making the system work
without knowing the exact code is
nearly impossible.
You should have received a card that
lists your audio system’s code
number and serial number. It is best
to store this card in a safe place at
home. In addition, you should write
the audio system’s serial number in
this Owner’s Manual. If you should
happen to lose the card, you must
obtain the code number from your
Honda dealer. To do this, you will
need the system’s serial number.
Theft Protection
Audio System
Comfort and Convenience Features
178
Diagnosing why your engine won’t
start falls into two areas, depending
on what you hear when you turn the
key to START (III):
You hear nothing, or almost
nothing. The engine’s starter
motor does not operate at all, or
operates very slowly.
You can hear the starter motor
operating normally, or the starter
motor sounds like it is spinning
faster than normal, but the engine
does not start up and run.
Turn the ignition switch to ON (II).
Turn on the headlights and check
their brightness. If the headlights
are very dim or don’t light at all,
the battery is discharged. See
on page
.
When you turn the ignition switch to
START (III), you do not hear the
normal noise of the engine trying to
start. You may hear a clicking sound
or series of clicks, or nothing at all.
Check these things:
Turn the ignition switch to START
(III). If the headlights do not dim,
check the condition of the fuses. If
the fuses are OK, there is proba-
bly something wrong with the
electrical circuit for the ignition
switch or starter motor. You will
need a qualified technician to
determine the problem. (See
on page
.)
Check the transmission interlock.
If you have a manual transmission,
the clutch pedal must be pushed
all the way to the floor or the
starter will not operate. With an
automatic transmission, it must be
in Park or Neutral.
320
337
Nothing Happens or the Starter
Motor Operates Very Slowly
Jump Starting
Emergency Towing
If Your Engine Won’t Start
Taking Care of the Unexpected
318
If the headlights dim noticeably or
go out when you try to start the
engine, either the battery is dis-
charged or the connections are
corroded. Check the condition of the
battery and terminal connections
(see page
). You can then try
jump starting the vehicle from a
booster battery (see page
).
In this case, the starter motor’s
speed sounds normal, or even faster
than normal, when you turn the
ignition switch to START (III), but
the engine does not run.
Are you using the proper starting
procedure? Refer to
on page
.
There may be an electrical
problem, such as no power to the
fuel pump. Check all the fuses
(see page
).
If you find nothing wrong, you will
need a qualified technician to find
the problem. See
on page
.
Your vehicle has the Immobilizer
System. You should use a
properly-coded master or valet key
to start the engine (see page
).
A key that is not properly coded
will cause the immobilizer system
indicator in the dash panel to blink
rapidly.
Do you have fuel? Turn the
ignition switch to ON (II) for a
minute and watch the fuel gauge.
The low fuel level warning light
may not be working, so you were
not reminded to fill the tank.
269
320
200
85
331
337
The Starter Operates Normally
Starting the
Engine
Emergency
Towing
If Your Engine Won’t Start
Taking Care of the Unexpected
319
If the electric motor will not close
the moonroof, do the following:
Check the fuse for the moonroof
motor (see page
). If the fuse
is blown, replace it with one of the
same or lower rating.
Try closing the moonroof. If the
new fuse blows immediately or the
moonroof motor still does not
operate, you can close the
moonroof manually.
Insert the moonroof wrench into
the socket behind this plug. Turn
the wrench until the moonroof is
fully closed.
Remove the wrench. Reinstall the
round plug.
To remove the round plug in the
center of the headliner, turn the
plug by using a screwdriver or
coin, then pry it out. Make sure to
align the tabs on the round plug to
the notches on the ceilling as
shown in the illustration.
Get the moonroof wrench out of
the tool kit under the cargo area
floor.
1.
2.
3.
4.
5.
6.
331
Closing the Moonroof
Taking Care of the Unexpected
330
ROUND PLUG
TAB
NOTCH
SOCKET
All the electrical circuits in your
vehicle have fuses to protect them
from a short circuit or overload.
These fuses are located in two fuse
boxes.
The under-hood fuse box is located
in the engine compartment on the
driver’s side. To open it, push the
tabs as shown.
The interior fuse box is underneath
the steering column. To remove the
fuse box lid, pull it toward you and
take the lid out of its hinges.
Fuses
Taking Care of the Unexpected
331
TAB
INTERIOR
UNDER-HOOD
If something electrical in your
vehicle stops working, the first thing
you should check for is a blown fuse.
Determine from the chart on pages
and
, or the diagram on the
fuse box lid, which fuse or fuses
control that component. Check those
fuses first, but check all the fuses
before deciding that a blown fuse is
not the cause. Replace any blown
fuses and check the component’s
operation.
Check each of the large fuses in
the under-hood fuse box by
looking through the top at the wire
inside. Removing these fuses
requires a Phillips-head screw-
driver.
Remove the cover from the fuse
box.
Turn the ignition switch to LOCK
(0). Make sure the headlights and
all other accessories are off.
3.
1.
2.
335
336
Checking and Replacing Fuses
Fuses
Taking Care of the Unexpected
332
BLOWN
FUSE
CONTINUED
If you cannot drive the vehicle
without fixing the problem, and you
do not have a spare fuse, take a fuse
of the same rating or a lower rating
from one of the other circuits. Make
sure you can do without that circuit
temporarily (such as the accessory
power socket or radio).
If you replace the blown fuse with a
spare fuse that has a lower rating, it
might blow out again. This does not
indicate anything wrong. Replace the
fuse with one of the correct rating as
soon as you can.
Look for a burned wire inside the
fuse. If it is burned, replace it with
one of the spare fuses of the same
rating or lower.
Check the smaller fuses in the
under-hood fuse box and all the
fuses in the interior fuse box by
pulling out each fuse with the fuse
puller provided in the under-hood
fuse box.
5.
4.
Fuses
Taking Care of the Unexpected
333
FUSE PULLER
BLOWN
If the replacement fuse of the
same rating blows in a short time,
there is probably a serious
electrical problem in your vehicle.
Leave the blown fuse in that
circuit and have your vehicle
checked by a qualified mechanic.
6.
Taking Care of the Unexpected
Fuses
334
Replacing a fuse with one that has a
higher rating greatly increases the
chances of damaging the electrical
system. If you do not have a replace-
ment fuse with the proper rating for the
circuit, install one with a lower rating.
ʵ
ʵ
ʵ
ˎ
ˎ
ˎ
No.
No.
CONTINUED
Amps.
Circuits Protected
Amps.
Circuits Protected
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
15 A
10 A
10 A
10 A
Ignition Coil
Daytime running lights
ACG
Not Used
7.5 A
20 A
7.5 A
7.5 A
7.5 A
7.5 A
10 A
10 A
20 A
20 A
15 A
15 A
7.5 A
20 A
20 A
20 A
20 A
20 A
Power Window Relay
Moonroof
Accessory, Radio
Rear Wiper
Meter
Not Used
Daytime running lights
SRS
Remote Control Mirrors
LAF Heater
Heated Seat
Fuel Pump
Turn Signal Lights
Front Wiper
Not Used
Front Right Power Window
Front Left Power Window
Rear Left Power Window
Rear Right Power Window
: On Canadian models
Rear Accessory Power Socket
Front Accessory Power Socket
Fuses
Taking Care of the Unexpected
335
INTERIOR FUSE BOX
ʵ
ʵ
ʵ
No.
Amps.
Circuits Protected
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
20 A
15 A
15 A
20 A
15 A
15 A
15 A
10 A
30 A
20 A
40 A
40 A
40 A
15 A
20 A
15 A
30 A
100 A
50 A
Condenser Fan
Small Light
Interior Light
Cooling Fan
Hazard
FI ECU
Horn, Stop
Not Used
Back Up
ABS Motor
Rear Defroster
Heater Motor
Power Window
Option
Left Headlight
Door Lock
Right Headlight
ABS F/S
Battery
Ignition 1
Spare Fuses
21
25
7.5A
30A
Taking Care of the Unexpected
Fuses
336
UNDER-HOOD FUSE BOX
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
Specifications
Technical Information
343
Air Conditioning
Battery
Tires
Alignment
Fuses
Lights
HFC-134a (R-134a)
17.0
18.7 oz (480
530 g)
SP-10
12 V
12 V
60/55 W
21/5 W
36 AH/5 HR
12 V
12 V
12 V
12 V
12 V
12 V
12 V
12 V
12 V
21 W
3 CP
8 W
4 CP
8 W
5 W
21 W
21/5 W
21 W
12 V
3 CP
Refrigerant type
Charge quantity
Lubricant type
Capacity
12 V
See page
335
or the fuse label
attached to the inside of the fuse
box door under the steering
column.
45 AH/20 HR
12 V
26 psi (180 kPa , 1.8 kgf/cm
)
26 psi (180 kPa , 1.8 kgf/cm
)
P205/70R15 95S
Size
Pressure
Toe-in
Camber
Caster
1°45’
0.08 in (2.0 mm)
0.0 in (0 mm)
See page
336
or the fuse box
cover.
Interior
Under-hood
Headlights
Front turn signal/side marker
lights
Parking lights
Rear turn signal lights
Stop/Taillights
Back-up lights
License plate light
Ceiling light
Spotlights
Cargo area Light
Rear side marker lights
High-mount brake light
Front
Rear
Front
Rear
Front
Front/Rear
Front
Rear
(H4/HB2)